Changing consumable parts on a Toyota Camry is a pleasure for the motorist. The engine oil filter is no exception. Just lift the front of the car, and right under the engine you will find both the drain plug and the filter housing. The filter is replaced together with an oil change. It is recommended to do this after 15,000 km, but this is an approximate number. If the car is operated under increased loads, this number will be reduced to 7,000 km.
So, let's begin.
1. Let's prepare tools and materials.
14 mm socket wrench – for drain plug;
a special key for unscrewing the plug at the bottom of the filter housing;
special key remover for the filter housing (indicated by an arrow);
container for collecting oil;
original filter;
oil (SAE OW 20);
paper towel, rags.

2.Important! Secure the raised machine before climbing to unscrew the plug and filter (they are indicated by arrows). Place the container, unscrew the plug (14 mm wrench) and drain the used oil.
Photo 2.

3. While the oil is draining, prepare a special key puller ( green arrow). Let's check the condition of the sealing gasket on the drain plug. It can be cut from paronite. We wrap the cork.


4.Using a puller, unscrew the filter housing.


5. We took the filter out of the housing and checked the oil-resistant sealing ring. It comes with a filter (check when purchasing). Let's replace the ring and clamp it with a clamping plug (the plug and the place where it needs to be screwed are indicated by a white arrow).

6.And here is the top of the case. Replaced the rubber sealing ring of the housing. We insert the filter into the housing. Further operations proceed in the reverse order.

7.Filter housing in place. Now you need to use special wrenches to tighten the filter cover and housing. There is no need to make excessive efforts.

8. Using the recommendations for changing the oil, fill it as much as indicated in the table.

The first number is the top level. The second number is the lower level. They are marked on the dipstick. Place the machine horizontally and fill with the upper level amount, then start the engine and stop it. Take the measurement again, the level will drop (the system will fill). Top up to normal and off you go.

Frequency of oil changes in automatic transmission Toyota Camry 2.5 l. V50 and other car models approximately once every 70 thousand mileage. The procedure is necessary in order to ensure better operation of the automatic transmission, extend the life of the mechanism, as well as the components associated with it. This stage of car maintenance is of great importance and should not be neglected.

How often does it need to be replaced?

During operation of the transmission of any car, especially if it is new, grinding of parts occurs, as a result of which a certain amount of chips gets into the oil. As it is produced, the fluid becomes more viscous and darker, and begins to interfere with the operation of the gears. That is why you should strictly observe the frequency of maintenance and update the oil on time. And therefore it is difficult to answer the question of how much oil is needed.

You can find out the exact number by looking at the service book, however, if the car is not new, the book may be lost. Different experts recommend different periods of consumable fluids - from 40 to 110 thousand km. The more often the oil is changed, the better, but for optimal operation of the gearbox you need to intervene no more than 70 thousand kilometers. This principle is considered the most suitable, since it requires less financial costs, and the oil is not changed at the most critical moment, managing to remove contaminants without becoming unsuitable for further use.

Selection of consumables

Changing the Toyota Camry automatic transmission oil should be done not only regularly, but also with the correct fluid. For work it is recommended to use original oil Toyota WS, which the manufacturer fills at the factory. However, this option is quite expensive and cannot always be found in stores. Most often, motorists use ATF Type-TLS-LV, which is its complete analogue.

The automatic transmission oil filter must be installed with a new one at every oil change. You can find both the original and cheaper analogues on sale; they are practically no different. It is worth paying attention to the fact that the Toyota Camry V40, regardless of engine power, is equipped with a gasket located in the gearbox. This part cannot be replaced with sealant; the gasket must be present.

Besides, Toyota Camry V40 requires 4 liters to replace, so it is more convenient to buy a large package at once, which will cost less than 4 1 liters.

How to replace it yourself?

Camry V40 2.4 and Camry 3.5 do not differ in transmission design, so they require the same maintenance. If you have certain skills, time and desire, you can change the oil in an automatic transmission yourself in a garage. However, it is worth warning that this is a rather labor-intensive procedure, and if you are afraid of doing it incorrectly, it is better to contact a specialized car service center where everything will be done according to the scheme. Change the oil completely garage conditions It won’t work; this requires the use of specialized equipment. Many make do with partial replacement, which is quite affordable.

On a Toyota Camry, replacement should be accompanied not only by replacing the gasket and filter, but also by removing the pan. This is necessary in order to check the condition of the automatic transmission, remove dirt, and check for chips. Changing the gearbox oil on a Camry is partially quite simple. All you need to do is drain the old fluid and add new one.

Keep in mind that at home it will not be possible to drain more than half of the liquid. When in automatic transmission On a Camry, the fluid is partially changed, forming an average mass suitable for further use. However, if large metal shavings or a large amount of it are detected, it is necessary not only to completely update the consumables, but also to repair the box, as this is a symptom of a gear malfunction.

For Camry quantity partial replacements should be twice the number of full replacements, since only 2.0 liters of fluid are poured, and accordingly, it becomes contaminated faster.

Work order

On a Camry V50 2.5 l, the oil is changed in the same way as on a Camry V40 3.5.

1. You need to work with the Kemri car by placing it on a horizontal surface that does not have slopes. The box must be slightly warmed up, as in the case of a manual transmission, when it is necessary to perform a similar operation. The transmission lever must be placed in all positions one by one, finally setting it to the parking mode;
2. After this, you need to measure the oil level in the automatic transmission; this procedure is also carried out after changing the oil in the Toyota automatic transmission. For this purpose, the design provides a special probe;
3. in order to drain the oil, you need to pull out the plug; prepare a container in advance so that the waste flows there; keep in mind that it is hot and will take about 15 minutes to drain;
4. after this you need to remove the gasket and unscrew the pan. Parts need to be washed and carefully inspected. You also need to unscrew the magnetic plug, wash it, and remove any chips, if any. There is no need to wait for the automatic transmission to cool down before adding new oil;
5. you need to replace the filter and gasket, put the pan in place and fill it with fresh water. Afterwards, you need to start the Camry car, let the power unit run for 5-7 minutes, switch the gearbox mode, and turn off the engine.

Oil change Toyota Camry

Engine oil is important element, which directly affects the operation of the unit. Without its timely replacement, the car will fail, and repairs will be expensive and difficult. Toyota Camry The V50, like other cars in this series, needs high-quality motor oil, the effect of which is clearly visible on engine performance. Lukoil oil is perfect

What fluid does the engine require?

What kind of oil to pour into a Camry is a rather pressing question. The manufacturer produces not only cars, but also adds to this list. When purchasing branded products, of course, do not worry about the comparability of the product, but the original cannot be purchased from every individual. Camry does well on principles synthetic oils, which have a viscosity of 5W-30 and 5W-40.

Read also

Toyota Genuine Motor Oil is a unique product; Which oil is better among analogues is worth thinking about. There are many brands, but it is better to put products into Camry from proven manufacturers who guarantee the highest level of quality of the product. Apply engine oil Lukoil with a viscosity of 5W40, unfortunately it will have to be changed more often than industrial grade. Camry V40 3.2.4 produced in 2007 runs on the unique Toyota 5W30 SM or SL. On the Russian market, the 1st option is more common, the 2nd is usually offered as non-original, therefore it is not recommended to contact a child.

Reasons for increased oil consumption

If the engine consumes a certain amount of consumable water during operation, if it is in good condition, the indicator is so low and practically unnoticeable, but the engine has begun to consume a lot, which means that the Camry model is experiencing certain difficulties. Excessive consumption does not occur by chance: it is recommended to diagnose the unit; lost time can cause a breakdown, the correction of which requires serious financial costs.

Not all oil is removed while the engine is running. oil scraper rings and goes into the pallet. A small part of it burns out: for example, for Camry V40 2.4.4 2007 produced by another similar car with an engine capacity of 3.5.5 liters. natural consumption is 0.05% - 0.25% of the total amount of water.

Read also

Consumption on a new engine is practically not noticeable, on used cars, for example, 2007 and older, This process is more pressing, because natural wear and tear occurs, due to which the appetite of the unit increases greatly. If you make frequent changes in the engine, and at the same time you have to pour more water with enviable consistency, this means that it is necessary to find the fault. You will like her more with an ordinary, or in other words, complex character. The main reasons for complex defects are as follows:

Toyota Camry XV50 Toyota Camry 2.5 2013 Oil and filter change

How much oil is in the Camry 2.5 engine.

oil filter 04152-31090 air filter 17801-28030 cabin filter 87139-50100 oil motor 5w30 5l.

1. wear piston rings. It occurs due to friction of parts. If the rings are worn, a gap will appear through which oil will escape through the Camry V40 2.4 exhaust system. If the motor has been overheated, the rings may be stuck. You can see this, of course, by the exhaust, which has acquired a blue color;
2. The walls of the cylinders also wear out during the use of the car. There is an option to bore these elements to a certain size or change the block completely. Option 1 is a little cheaper;
3. it happens that Camry V40 2.7.4 eats oil due to a problem with valve stem seals. These are oil seals that come in variations and lose their elasticity. It's quite difficult to change them technical level, however relatively cheap. Complete disassembly of the car engine is not necessary;
4. on 2007 Camry There is a widespread problem with the release when oil drips from under the cylinder head gasket. There is a problem due to the age of the car. New Camry They usually don’t suffer from such a problem, but it is recommended to continue checking the tightness of the bolts. If the car is old, it is recommended to change the gasket. Over time it burns out;

How to change it yourself?

Substitution oils Toyota Camry is required approximately once every 10 thousand kilometers. These are reasonable times, where a lot of dirt does not have time to accumulate, here the liquid settles down enough to be used up. If you use a brand name, of course, postpone the replacement for thousands of kilometers; if Lukoil, it is better not to deviate too much.

If you wish, you can change the engine oil in your garage. For this purpose, you need to be well prepared, have the necessary tools, filters and gaskets, as well as a container for waste water.

Read also

Clear quantity oils, needed for substitution, is indicated in service book. If it is not there, you will need 4.4 - 4.3 liters for the engine, 4.4 liters for the 2.7.5 engine.

Changing the engine oil is done according to the following scheme:

1. The car is placed over the pit, in other words, driven onto the overpass. The engine needs to be warmed up beforehand;
2. after a while, it is necessary to remove the crankcase protection element, unscrew the drain plug, the oil will drain into a substitute bucket. This will take about a quarter of an hour;
3. then you need to change the filter, tighten the drain plug, putting it back;
4. refilling of the new one occurs through the cap located on the engine, it is under the hood;
5. check the water level, start the car, wait about a minute until the engine shows that it is working correctly, and turn it off again;
6. At the very end we check the oil again. We do this when the engine has cooled down; if the level is insufficient, you need to top it up. If there is a lot of water, there is an option to leave it as it happens, the car itself will squeeze out the excess.

Toyota Camry is a popular middle and business class car almost all over the world, which is affordable for many adherents of the present Japanese quality. Cars from this model line have a long service life and often last up to a mileage of 1 million km. To prevent premature breakdowns and extend the period of effective operation of the car, you should adhere to the maintenance schedule and undergo renovation work before breakdowns occur on a serious scale.

Changing automatic transmission oil Toyota Camry 2.5

Transmission automatic switching speeds on the Toyota Camry create almost all the conditions for comfortable driving. Mechanism of this type does not distract the driver’s attention from the road by switching lever positions and independently selects the optimal speed.

The Toyota Camry 2.5 automatic transmission oil is changed every time the odometer reaches 90 thousand km. During this period of operation, ATP fluid almost completely loses its working properties and does not prevent overheating of transmission parts.

It is strictly not recommended by the car manufacturer to service the Toyota Camry automatic transmission yourself. Errors made during the maintenance process can negatively affect the functionality of the transmission and even cause it to fail. Automatic transmission repair on a car of this model is expensive, difficult to perform and labor-intensive work. Therefore, you will have to spend a lot of money, effort and nerves to restore the machine’s functionality.

Oil change in Toyota V50 at the Autopilot technical center

Maintenance of the Toyota Camry power unit must be carried out much more often than the automatic transmission. Engine oil loses performance characteristics after a mileage of 10-15 thousand km. If vehicle It is used lightly and should be serviced once a year.

In Moscow, carry out a lubricant change Toyota engine Camry, as well as other consumables at a competitive price, can be purchased at the Autopilot technical center. By contacting us, you will provide yourself with such advantages as:

• high quality car service provided by experienced and qualified professionals;
• guarantee for all services of masters;
• affordable pricing policy for motorists.

Do you need an oil change for Toyota Camry 2.5 V50 in Moscow? Visit the Autopilot technical center!

Car manufacturing plants great attention pay consumables, the operating instructions indicate all the necessary lubrication parameters. Car enthusiasts, when choosing oils for summer or winter, must take into account the requirements of car manufacturers, otherwise the engine may quickly fail. We invite you to familiarize yourself with the parameters of the recommended engine oil for Toyota Camry.

1994 model

The Toyota Camry automaker insists on using universal lubricants of the SG or SG/CD class according to the API system. To select the viscosity, you must use scheme 1.

Scheme 1. Predicted range of temperatures outside the car until the next oil change.

In accordance with scheme 1, when the thermometer reading is above -23.5 0 It is recommended to fill with liquids 10w-30, 10w-40, 10w-50. If the thermometer reading is above -12.5 0 C, then it’s worth pouring 20w-40, 1-20w-50. At temperatures below +10 0 You need to use 5w-30 fluid.

Refill tanks taking into account the oil filter are:

• 3.8 l for 5S-FE auto engines;
• 4.5 l if the engine is 3VZ-FE;
• 5.0 l corresponds to 1MZ-FE car engines.

Toyota Camry XV20 1996-2001

1998 model

• for 1MZ-FE motors, SH class lubricant according to API standards;
• for 5S-FE car engines, motor fluids of group SG and higher; in the absence of woven motor oil, it is permissible to pour class SF.

To select the viscosity parameters of the lubricant, Scheme 2 is used.

Scheme 2 Predicted temperature range outside the car until the next oil change.

In accordance with scheme 2 at a temperature range above -18 0 It is necessary to use lubricants 15w-40 or 1-20w-50. If the thermometer is below +10 0 C, use 5w-30 motor oils.

Refill containers:

1. Auto engines 1MZ-FE:

• 5.5 l dry engine;
• 7 l with change oil filter.

1. Motors 5S-FE:

• 4.3 L dry engine;
• 3.6 l with oil filter change.

Toyota Camry XV30 2001-2006

2005 model

1. According to the API system, groups SJ or SL, having a viscosity of 20w-50 or 15w-40, are used at air temperatures above -12.5 0 C (see diagram 3).
2. In accordance with API classification classes SJ or SL, designated “Energy Conserving” or universal motor oils certified according to ILSAC. The applied viscosity of such lubricants is 10w-30 at temperatures above -18 0 C, or 5w-30 if the air temperature is below +10 0 C. When choosing a viscosity indicator, take into account diagram 3.

Scheme 3. Assumed temperature Range before the next oil change.

The amount of lubricant that will be needed during subsequent replacement is:

• 3.8 l with an oil filter or 3.6 l without an oil filter for 1AZ-FE engines;
• 4.3 l including filter or 4.1 l without oil filter for 2AZ-FE engines;
• 4.7 l with an oil filter or 4.5 l without an oil filter in the case of 1MZ-FE engines.

Approximate volume lubricant which needs to be added so that the lubricant level is between the lower and upper level marks on the Toyota Camry dipstick is:

• 1.0 l for 1AZ-FE engines;
• 1.5 l in the case of power units 2AZ-FE and 1MZ-FE.

Toyota Camry XV40 2006-2011

2008 release

1. All-season motor fluids with the designation “Toyota Genuine Motor Oil” or motor oils with similar parameters, having the appropriate markings or approvals on the canister.
2. According to API standards, acceptable lubricant classes are SL or SM. Viscosity parameter according to the SAE system 20w-50 or 15w-40 at a temperature above -12.5 0 C (temperature selected according to scheme 4).
3. In accordance with the API classification, types of motor oils are SL or SM, designated “Energy Conserving” (energy-saving) or all-season lubricants according to ILSAC. Viscosity is selected 10w-30 when the thermometer reading is above -18 0 C, or 5w-30 if the air temperature is below +10 0 C (temperature indicators are taken from diagram 4).

Scheme 4. Dependence of the viscosity index of motor oil on the temperature of the region in which the car will be operated.

Refill tanks for Toyota Camry:

1. Engine 2AZ-FE:

• 4.3 l with oil filter;
• 4.1 l excluding oil filter.

1. Auto engine 2GR-FE:

• 6.1 l with oil filter;
• 5.7 l without oil filter.

Toyota Camry XV50 since 2011

2013 model

According to the operating instructions lubricating fluid for Toyota Camry engines - this is original Toyota oil or lubricants from other companies that have the parameters required by the car manufacturer. The class, type and viscosity of the oil are determined by the type of engine.

Power units 6AR-FSE and 2AR-FE

According to the manual, it is necessary to fill in oils with a viscosity index of 0w-20, 5w-20, 5w-30 or 10w-30, corresponding to classes SL or SM with the designation “Energy Conserving” according to the API system. It is acceptable to use universal lubricants certified according to ILSAC and having a viscosity parameter of 15w-40. You can also use motor oils of groups SL, SN or SM according to the API system.

To select the viscosity depending on the temperature outside the car, use diagram 5.

Scheme 5. The influence of air temperature on the selection of motor oil viscosity.

According to scheme 5, at extremely low temperatures it is necessary to fill in lubricants 0w-20, 5w-20, 5w-30. Motor oils with a viscosity parameter of 10w-30 or 15w-40 should be used if the thermometer is above -18 0 Otherwise, starting the engine will be difficult.

The volume of engine oil required during replacement is 4.4 liters including the oil filter and 4.0 liters without replacing the oil filter.

Auto engines 2GR-FE

• SL or SM with the designation “Energy Conserving” (energy saving);
• SN marked “Resource-Conserving” (resource-saving).

You can also pour lubricants certified by ILSAC and having a viscosity parameter of 15w-40 or use oil groups SL, SM and SN with the recommended viscosity index.

You can select the viscosity parameter according to scheme 6.

Diagram 6. Predicted temperature range until next shift motor fluid.

According to scheme 6, at extremely low temperatures it is necessary to use 5w-30 lubricants, and when the thermometer reading is above -18 0 C, pour 10w-30 or 15w-40.

The volume of engine fluid required when replacing is 6.1 liters with oil filter replacement and 5.7 liters excluding the oil filter.

Conclusion

By using the recommended engine oil for Toyota Camry, you can increase the life of the engine and lubrication system. The fact is that the lubricant creates a protective film on the surface of the internal elements of the car engine, the properties of which depend on the quality parameters of the lubricant. The thicker the car oil, the thicker the protective film will be; such oils should be used in the summer; thinner lubricants are used in winter; they ensure cold starting of the engine. If you use an oil that does not match the parameters, the film may break and the engine will start to run “dry” - this will lead to its breakdown.

When replacing lubricant, consider:

• The manual indicates the reference volume of oil that will be needed when changing the lubricant, in real conditions it may be slightly different;
• Overfilling the vehicle oil above the maximum mark on the dipstick is unacceptable, therefore, after adding lubricant, it is necessary to check the lubricant level.

Watch a video on how to change the oil in a Toyota Camry with your own hands:

Recommended engine oil for Toyota Avensis