You will need: keys "for 10", "for 12", "for 14", heads "for 15", "for 19", a hammer.
Remove the cylinder head.
Remove the engine oil sump and crankcase gasket.
Remove the oil pump.
Unscrew the nuts 1 of the connecting rod bolts and remove the cover 2 of the connecting rod.
If the lid is tight, knock it down with light hammer blows.
Remove the insert from the cover.
Push the piston out of the cylinder and remove it with the connecting rod.
Remove the bushing from the connecting rod.
If you are going to install the old liners, mark them with the cylinder number.
Remove the piston with a connecting rod from the cylinder carefully so as not to damage the cylinder mirror.
Check the marks on the connecting rod and its cover. If the marks are not visible, mark the connecting rod and cover with the cylinder number.
Remove the remaining pistons with connecting rods.
Remove the piston rings with a puller or, if it is missing, carefully unfold the rings at the locks.
Do not unbend the rings more than is required to remove them, otherwise the rings may not be shaped or broken.
8. Remove the retaining rings from both sides of the piston.
Press out the piston pins with a special tool.
If no device is available, the piston pins can be knocked out by light hammer blows through the mandrel 1. This must be done by weight to avoid damaging the piston. Remove connecting rod 2 from piston 3.
Remove the rest of the pistons from the connecting rods.
Wash all parts in gasoline. Remove carbon deposits from pistons.
Remove carbon deposits from the piston ring grooves with a piece of an old piston ring.
Examine the pistons. If they have scuff marks, traces of burnout, replace the pistons.
Measure the piston diameter. If it is less than 95.4 mm, replace the piston.
The piston diameter is measured in a plane perpendicular to the piston pin axis, 8.0 mm below the piston pin axis.
The piston is installed in the cylinder with a clearance of 0.036–0.060 mm.
The pistons are divided by diameter into five size groups: A, B, C, D, D. The lettering is stamped on the piston crown.
When matching the piston to the cylinder, the above clearance must be ensured.
Extremely allowable clearance between the piston and the cylinder 0.25 mm.
The piston-to-cylinder clearance can be determined by measuring the piston and cylinder. The spare parts are supplied with pistons of two repair sizes: with a diameter increased by 0.5 and 1.0 mm.
On one of the bosses under the piston pin there is an inscription “409” (piston of nominal diameter), “409AP” (diameter increased by 0.5 mm) or “409BR” (diameter increased by 1.0 mm).
Measure the piston ring-to-piston groove clearance at several locations around the circumference of the piston.
The gap should be between 0.060-0.096 mm for compression rings and 0.115-0.365 mm for oil scraper ring.
If the clearances exceed the specified values, the rings or pistons must be replaced.
Measure the clearances in the locks piston rings.
To do this, insert the ring into the cylinder and push it with the piston like a mandrel so that the ring fits in the cylinder evenly, without distortions.
Measure the gap in the lock (connector) of the ring with a feeler gauge; it should be within 0.3–0.6 mm for compression rings and 0.5–1.0 mm for oil scraper disks.
If the clearance exceeds the specified, replace the ring.
If the gap is less, you can file the ends of the ring with a file clamped in a vice, moving the ring up and down the file.
15. Check the seating of the piston pin in the upper connecting rod head.
The gap between the pin and the bushing of the upper connecting rod head should be in the range of 0.0045-0.0095 mm.
Pins, pistons and connecting rods are divided into four size groups and are marked with paint.
The finger is marked on the inner surface at one end, the connecting rod - on the rod, the piston - on the lower surface of one of the bosses, or a Roman numeral is knocked out on the piston bottom.
Lightly lubricate the piston pin with a clean engine oil and insert into the upper connecting rod head. The finger should enter the head from the effort of the hand evenly, without jamming.
The connecting rod must rotate on the piston pin under its own weight from a horizontal position.
In an upright position, the pin should not protrude or fall out of the connecting rod head due to its own weight.
Piston pin and connecting rod must be in the same size group or adjacent groups.
16. Pistons with piston rings, pins and connecting rods are selected by weight. The difference in weight for one engine should be no more than 10 g.
17. Inspect the connecting rod bushings. If they have scuffs, chipping or other damage, replace the liners.
18. Install the caps on the connecting rods and measure the diameter of the hole in the lower connecting rod head.
The nominal hole diameter is 60 + 0.019 mm, the maximum permissible diameter is 60.03 mm.
If the measured diameter exceeds the maximum permissible, replace the connecting rod with a cap.
Measure the diameter of the bore in the upper connecting rod bushing.
The nominal hole diameter is 22 + 0.007 –0.003 mm, the maximum allowable diameter is 22.01 mm.
If the measured diameter exceeds the limit, replace the connecting rod. Connecting rod dimensions piston group are given in the table.
* Tolerance 0.06 mm divided into 5 groups (every 0.012 mm)
Assemble piston 4 with connecting rod 3. Preheat the piston to a temperature of 60–80 ° C.
Then quickly insert the connecting rod into the piston so that the inscription “ Front"On the piston and the protrusion" A»Were on one side of the connecting rod, and press in the piston pin 6 with a maximum tightness of 0.0025 mm.
Install the circlip 5. Slide the piston rings onto the piston using a puller.
The upper compression ring has the inscription "Top", the ring must be installed on the piston with this inscription to the bottom of the piston.
A groove is made on the lower compression ring on the inner side, the ring must be installed with this groove up to the piston bottom.
Insert the insert 7 into the lower head of the connecting rod - the fixing protrusion ("lock") on the insert should go into the recess in the lower head of the piston.
Insert the insert 1 into the cover 2 of the connecting rod - the locking projection ("lock") of the insert must enter the recess in the cover.
Lubricate the cylinder, piston 4, crankshaft connecting rod journal and liners 1 and 7 with clean engine oil.
Orient the piston rings so that the compression ring locks are at an angle of 180 ° to each other, the oil scraper ring disc locks are also at an angle of 180 ° to each other and at 90 ° to the compression ring locks, the oil scraper ring expander lock is at an angle of 45 ° to the lock of one of the oil scraper discs.
Turn crankshaft so that the connecting rod journal of the cylinder in which the piston is installed is at BDC.
Insert the piston with the connecting rod into the cylinder so that the inscription “ Front»On the piston pin boss is facing the front of the engine (towards the camshaft drive).
In order not to damage the cylinder mirror, we recommend that you put soft bushings on the connecting rod bolts (for example, cut rubber or plastic hoses).
Using a special mandrel, crimp the piston rings and push the piston into the cylinder with light blows with a hammer handle, while the mandrel must be firmly pressed against the block, otherwise the piston rings may break.
Move the piston down so that the lower head of the connecting rod sits on the connecting rod journal of the crankshaft, remove the hose cutters from the connecting rod bolts.
Install the connecting rod cover 2 onto the connecting rod bolts so that the shoulder " B"On the connecting rod cover was on the same side as the protrusion" A»On the lower head of the connecting rod; the cylinder numbers stamped on the connecting rod and the cover were located on one side, and the "locks" of the liners were opposite each other.
Install the connecting rod bolt nuts and tighten them to a torque of 68–75 Nm (6.8–7.5 kgf · m).
Install the remaining pistons with connecting rods in the same way.
Turn the crankshaft several times, it should rotate easily, without jamming.
Install the oil pump, oil pan and cylinder head.
You will need: keys "for 10", "for 12", "for 14", heads "for 15", "for 19", a hammer.
1. Remove the cylinder head (see. "Replacing the cylinder head gasket").
2. Remove the engine oil sump and crankcase gasket (see. "Replacing the oil sump seal").
3. Remove the oil pump (see. "Removal, repair and installation of the oil pump").
4. Unscrew the nuts 1 of the connecting rod bolts and remove the cover 2 of the connecting rod. If the lid is tight, knock it down with gentle hammer blows. Remove the insert from the cover.
5. Push the piston out of the cylinder and remove it with the connecting rod. Remove the bushing from the connecting rod.
6. Remove the remaining pistons with connecting rods.
7.Using a puller, remove the piston rings; in the absence of a puller, carefully unfold the rings at the locks.
10. Remove the remaining pistons from the connecting rods.
11. Wash all parts in gasoline. Remove carbon deposits from pistons. Remove carbon deposits from the piston ring grooves with a piece of an old piston ring.
12. Inspect the pistons. If they have scuff marks, traces of burnout, replace the pistons. Measure the piston diameter. If it is less than 95.4 mm, replace the piston. The diameter of the piston is measured in a plane perpendicular to the axis of the piston pin, 8.0 mm below its axis. The piston is installed in the cylinder with a clearance of 0.036–0.060 mm. The pistons are divided by diameter into five size groups: A, B, C, D, D. The lettering is stamped on the piston crown. When matching the piston to the cylinder, the above clearance must be ensured. The maximum permissible clearance between the piston and the cylinder is 0.25 mm. The piston-to-cylinder clearance can be determined by measuring the piston and cylinder. The spare parts are supplied with pistons of two repair sizes: with a diameter increased by 0.5 and 1.0 mm. On one of the bosses under the piston pin the inscription is cast: “409” (piston of nominal diameter), “409AP” (diameter increased by 0.5 mm) or “409BR” (diameter increased by 1.0 mm).
| |
13. Measure the piston ring-to-piston groove clearance at several locations around the circumference of the piston. The clearance should be between 0.096–0.060 mm for compression rings and 0.115–0.365 mm for the oil scraper ring. If the clearances exceed the specified values, the rings or pistons must be replaced. | 14. Measure the clearances in the piston ring joints. To do this, insert the ring into the cylinder and push it with the piston like a mandrel so that the ring fits in the cylinder evenly, without distortions. Measure the gap in the lock (in the connector) of the ring with a feeler gauge; it should be within 0.3–0.6 mm for compression rings and 0.5–1.0 mm for oil scraper discs. If the clearance exceeds the specified, replace the ring. If the gap is less, you can file the ends of the ring with a file clamped in a vice. In this case, move the ring up and down the file. |
15. Check the seating of the piston pin in the upper connecting rod head. The gap between the pin and the bushing of the upper connecting rod head should be in the range of 0.0045-0.0095 mm. Pins, pistons and connecting rods are divided into four size groups and are marked with paint. The finger is marked on the inner surface at one end, the connecting rod - on the rod, the piston - on the lower surface of one of the bosses, or a Roman numeral is knocked out on the piston bottom. Dimensional groups of pistons, connecting rods and pins are given in table. 5.3.
Lightly lubricate the gudgeon pin with clean engine oil and insert into the upper connecting rod head. The finger should enter the head from the effort of the hand evenly, without jamming. The connecting rod must rotate on the piston pin under its own weight from a horizontal position. In an upright position, the pin should not protrude or fall out of the connecting rod head due to its own weight. Piston pin and connecting rod must be in the same or adjacent size groups.
Table 5.3 Dimensional groups of pistons, connecting rods and pins of engines mod. ZMZ-409.10
16. Pistons with piston rings, pins and connecting rods are selected by weight. The difference in weight for one engine should be no more than 10 g.
17. Inspect the connecting rod bushings. If they have scuffs, chipping and other defects, replace the liners.
18. Install the caps on the connecting rods and measure the diameter of the hole in the lower head of the connecting rod. The nominal hole diameter is 60 + 0.019 mm, the maximum permissible diameter is 60.03 mm. If the measured diameter exceeds the maximum permissible, replace the connecting rod with a cap. Measure the diameter of the bore in the upper connecting rod bushing. The nominal hole diameter is 22 + 0.007 –0.003 mm, the maximum allowable diameter is 22.01 mm. If the measured diameter exceeds the limit, replace the connecting rod. The dimensions of the connecting rod-piston group are given in table. 5.4.
Table 5.4 Rated and limit permissible sizes and landing of mating parts of the connecting rod-piston group of the engine mod. ZMZ-409.10
* Tolerance 0.06 mm is divided into five groups (every 0.012 mm).
19. Assemble piston 4 with connecting rod 3. Preheat the piston to a temperature of 60–80 ° C. Then quickly insert the connecting rod into the piston so that the inscription "Front" on the piston and the projection A on the connecting rod are on one side, and press in the piston pin 6 with a maximum tightness of 0.0025 mm. Install the retaining rings 5. Slide the piston rings onto the piston using a puller.
Insert the insert 7 into the lower head of the connecting rod, while the retaining protrusion ("lock") on the insert must enter the recess in the lower head of the piston. Insert the insert 1 into the cap 2 of the connecting rod, while the retaining protrusion ("lock") of the insert must enter the recess in the cover. Lubricate the cylinder, piston 4, crankshaft connecting rod journal and liners 1 and 7 with clean engine oil. Rotate the piston rings so that the locks of the compression rings are at an angle of 180 ° to each other, the locks of the oil scraper ring discs are at an angle of 180 ° to each other and at an angle of 90 ° to the locks of the compression rings, the lock of the oil scraper ring is at an angle of 45 ° to the lock one of the oil scraper discs. Turn the crankshaft so that the connecting rod journal of the cylinder in which the piston is installed is at bottom dead center (BDC). Insert the piston and connecting rod into the cylinder with the “Front” lettering on the piston boss facing the front of the engine (camshaft drive).
Using a special mandrel, crimp the piston rings and push the piston into the cylinder with light blows with a hammer handle, while the mandrel must be firmly pressed against the block, otherwise the piston rings can be broken. Move the piston down so that the lower end of the connecting rod sits on the crankshaft connecting rod journal, and remove the hose cutters from the connecting rod bolts. Install the connecting rod cover 2 on the connecting rod bolts, ledge B on the connecting rod cover must be on the same side as the protrusion A on the lower head of the connecting rod, the cylinder numbers stamped on the connecting rod and the cover must be located on one side, and the "locks" of the liners - opposite each other.
20. Wrap the nuts of the connecting rod bolts and tighten to a torque of 68–75 N · m (6.8–7.5 kgf · m).
21. Install the remaining pistons with connecting rods in the same way.
22. Turn the crankshaft several times; it should rotate easily, without jamming.
23. Install the oil pump, oil pan and cylinder head.
The grounds for disassembling and repairing the engine are: a drop in engine power, a decrease in oil pressure, a sharp increase in oil consumption (over 450 g per 100 km of run), engine smoke, increased fuel consumption, a decrease in compression in the cylinders, as well as noise and knocking.
When repairing engines, you must take them into account. design features... Engine cylinder block mod. The 4218, unlike the engine block of models 414, 4178 and 4021.60 with wet, easily removable liners, has a monolithic design with cast liners without seals. The sleeves in it are bored to the size of 100 mm (instead of 92 mm). The dimensions of the pistons, piston pins and rings have been increased accordingly. The pistons have a combustion chamber in the bottom. Piston pins have increased wall thickness, connecting rods - 7 mm longer.
When disassembling the engine, carefully check the reusability of each part. Criteria for assessing the possibility of further use of parts are given in
Engine performance can be restored by replacing worn parts with new nominal sizes or by restoring worn parts and using new oversized parts associated with them.
For these purposes, pistons, piston rings, liners for connecting rod and main bearings of the crankshaft, inlet and outlet valve seats, camshaft bushings and a number of other parts and kits of overhaul sizes are produced. The list of parts and kits of nominal and overhaul dimensions is given in
Values of clearances and tightness in the engine
A decrease or increase in clearances against the recommended ones worsens the lubrication conditions for rubbing surfaces and accelerates wear. Reducing the tightness in stationary (press) landings is also highly undesirable. For parts such as guide bushings and plug-in exhaust valve seats, reducing the interference will impair the transfer of heat from these parts to the cylinder head wall. Use the data when repairing the engine. (and )
Removal and installation of the engine on cars of the UAZ-31512 family
Before removing the engine from a vehicle in a viewing ditch, do the following:
1. Drain the cooling system and the oil from the engine crankcase.
2. Remove the air filter.
3. Disconnect the front exhaust pipe from the engine.
4. Disconnect the cooling system, heater and oil cooler hoses from the engine.
5. Disconnect and remove the cooling system radiator.
6. Disconnect the air and throttle valve rods from the carburetor.
7. Disconnect all electrical wiring from the engine.
8. Disconnect the clutch slave cylinder and the connecting rod from the clutch housing.
9. Remove the bolts securing the front engine mounts cushions together with the lower mounts cushions.
10. Install the special bracket on the second and fourth pins of the block head (), counting from the front end of the block.
11. Lift the engine with a hoist and disconnect the transmission from the engine.
12. Raise the engine and remove it from the car, while the gearbox is transfer case remain on the vehicle frame.
Install the engine on the vehicle in reverse order.
The engine can be removed by lowering it together with the gearbox and transfer case, it is necessary to remove the cross member. This method is much more complicated than the first.
Features of removal and installation of the engine on UAZ cars of wagon layout
To remove the engine, you must:
1. Follow the instructions of p. 1–10 of the section "Removal and installation of the engine on vehicles of the UAZ-31512 family".
2. Remove the seats and the hood cover.
3. Open the hatch in the cab roof, pass the hook with the cable (chain) of the lifting mechanism through it and hook the hook into the shackle.
4. Lift the engine a little and disconnect it from the transmission.
5. To facilitate removal of the engine, install a plank in the doorway that does not sag under the weight of the engine.
6. Lift the engine up to the opening in the hood with a lifting mechanism and, being careful, lift it out through the doorway along the plank.
Install the engine in reverse order.
Disassembly and assembly of the engine
Thoroughly clean the engine from dirt and oil before disassembling.
Disassemble and assemble the engine on a turntable using tool kits, for example, models 2216-B and 2216-M GARO, as well as special tools and accessories specified in Appendix 2.
With an individual method of repairing the engine, parts suitable for further work should be installed in the same places where they were worn in. To ensure this, mark the pistons, piston rings, connecting rods, piston pins, bushings, valves, rods, rocker arms and pushers when removing in any way that does not cause damage (punching, writing, paint, attaching tags, etc.).
With any type of repair, you must not uncomplete the connecting rod caps with connecting rods, rearrange the clutch housing and main bearing caps from one engine to another, or swap the middle main bearing caps in one block, since these parts are processed together.
When replacing the clutch housing, check the alignment of the hole that serves to center the gearbox with the crankshaft axis, as well as the perpendicularity of the rear end of the clutch housing relative to the crankshaft axis. When checking, fasten the indicator stand to the crankshaft flange. In this case, the clutch must be removed. The runout of the hole and the end of the crankcase should not exceed 0.08 mm.
After disassembling the engine, thoroughly degrease the parts, remove carbon deposits and tarry deposits.
Remove carbon deposits from pistons, intake valves and combustion chambers mechanically or chemically.
The chemical method for removing carbon deposits consists in keeping the parts in a bath with a solution heated to 80–95 ° С for 2–3 hours.
To clean aluminum parts, use the following solution composition (in g per 1 liter of water):
Soda ash (Na2CO3) ..... 18.5
Laundry or green soap ..... 10
Liquid glass (Na2SiO3) ..... 8.5
To clean steel parts, use the following solution composition (in grams per liter of water):
Caustic soda (NaOH) ..... 25
Soda ash (Na2CO3) ..... 33
Laundry or green soap ..... 3.5
Liquid glass (Na2SiO3) ..... 1.5
After cleaning, rinse the parts with hot (80–90 ° C) water and blow them off with compressed air.
Do not wash aluminum and zinc alloy parts in solutions containing alkali (NaOH).
Observe the following when assembling the engine:
1. Wipe and blow the parts with compressed air, and lubricate all rubbing surfaces with engine oil.
2. Threaded parts (pins, plugs, fittings), if they were turned out or were replaced during the repair process, install on the red lead.
3. One-piece connections (for example, a plug of the cylinder block) should be installed on nitro varnish.
4. Tighten the bolts and nuts with a torque wrench, tightening torque, N · m (kgf · m):
Cylinder head stud nuts ..... 71.6–76.5 (7.3–7.8)
Connecting rod bolt nuts ... 66.7-73.5 (6.8-7.5)
Crankshaft main bearing cap stud nuts ... 122.6-133.4 (12.5-13.6)
Flywheel-to-crankshaft bolt nuts ..... 74.5-81.4 (7.6-8.3)
Cylinder block repair
The pairing of the wearing parts is carried out mainly by replaceable parts, which allows the cylinder block to be repaired by regrinding or replacing the liners, replacing worn out camshaft bushings with semi-finished ones, followed by processing them to the required size, replacing the crankshaft main bearing shells. The restoration of the operability of a pair of cylinder block bore-pusher due to their insignificant wear is reduced to replacing the pushers.
Repair and replacement of cylinder liners
The maximum permissible wear of the cylinder liners should be considered an increase in the clearance between the liner and the piston skirt to 0.3 mm. In the event of such wear, press the liner out of the cylinder block using a puller 1 () and bore to the nearest piston oversize with a machining tolerance of +0.06 mm.
Do not clamp the sleeve into the chuck during machining, as this will deform the sleeve and distort its dimensions.
Fasten the sleeve in the tool, which is a sleeve with landing collars with a diameter of 100 and 108 mm. Insert the sleeve into the bushing until it stops in the upper shoulder, which is clamped with a cover ring in the axial direction. After processing, the cylinder liner mirror should have the following deviations:
1. Ovality and taper no more than 0.01 mm, and the larger base of the cone should be located in the lower part of the sleeve.
2. Barrel shape and corset - no more than 0.08 mm.
3. The beating of the cylinder mirror relative to the landing belts with a diameter of 100 and 108 mm is not more than 0.01 mm.
After pressing the liner into the cylinder block, check the protrusion of the upper end of the liner above the upper plane of the block (). The amount of protrusion should be 0.005–0.055 mm. If there is insufficient protrusion (less than 0.005 mm), the head gasket may be punctured; in addition, coolant will inevitably enter the combustion chamber due to insufficient sealing of the upper collar of the liner with the cylinder block. When checking the amount of protrusion of the end of the sleeve over the block, it is necessary to remove the rubber O-ring from the sleeve.
To prevent the liners from falling out of the slots in the block during repairs, secure them with washers 2 and bushings 3, which are put on the cylinder head mounting studs, as shown in.
After worn out, replace the cylinder liners bored to the third repair size of the piston with new ones.
Cylinder head repair
The main defects in the cylinder head that can be eliminated by repair include: warpage of the contact plane with the cylinder block, wear of valve seats and valve guides.
The non-straightness of the plane of the head in contact with the block, when checking it on the control plate with a probe, should not be more than 0.05 mm. Eliminate slight warpage of the head (up to 0.3 mm) by scraping the plane along the paint. For warpage exceeding 0.3 mm, the head must be sanded.
Replacing the piston rings
Replace the piston rings after 70,000–90,000 km (depending on the operating conditions of the vehicle).
Piston rings are installed three on each piston:
two compression and one oil scraper. Compression rings are cast from special cast iron. The outer surface of the upper compression ring is porous chrome plated, and the surface of the second compression ring is tin plated or has a dark phosphate coating.
On the inner cylindrical surfaces of both compression rings, grooves (, a) are provided, due to which the rings twist slightly when the piston moves downward, which contributes to better removal of excess oil from the surface of the sleeves. The rings must be installed on the piston with the grooves up, towards the piston crown.
The UMZ – 4218.10 engine can be equipped with two versions of compression rings (, b, c).
One version of the upper compression ring 2 (b) has a groove on the inner cylindrical surface. The ring must be installed on the piston with the groove up.
Another version of the upper compression ring 2 (c) has a barrel-shaped profile of the outer surface, there is no groove on the inner cylindrical surface of the ring. The position of the ring when installed in the piston groove is indifferent.
The lower compression ring 3 (, b, c) is of the scraper type; it has an annular groove on the lower end surface, which, together with the tapered outer surface, forms a sharp lower edge ("scraper"). The ring is made in two versions - with a groove on the inner cylindrical surface of the ring (, b) and without a groove (, c). The ring must be installed on the piston with the sharp edge "scraper" down.
The oil scraper ring is composite, has two annular discs, radial and axial expanders. The outer surface of the oil scraper ring disc is hard chrome plated.
The lock of the rings is straight.
Piston rings of repair sizes (see) differ from rings of nominal sizes only in outer diameter.
Oversized rings can be installed in worn-out cylinders with the next smaller oversize by sawing their joints until a gap in the lock of 0.3–0.5 mm is obtained (0.3–0.65 mm for engines mod. 4218).
Check the side clearance in the ring joint as shown in. Fit rings to regrind cylinders along the upper part, and to worn ones - along the lower part of the cylinder (within the piston ring stroke). When adjusting the ring, install the ring in the cylinder in the working position, i.e. in a plane perpendicular to the axis of the cylinder, to do this, advance it in the cylinder using the piston head. The planes of the joints when the ring is compressed must be parallel.
After adjusting the rings to the cylinder-frames, check the lateral clearance between the rings and grooves in the piston (), which should be: 0.050–0.082 mm for the upper compression ring, 0.035–0.067 mm for the lower compression ring. With large gaps, replacing only the piston rings will not exclude increased consumption oil due to the intensive pumping of it by rings into the space above the piston. In this case, replace the pistons at the same time as replacing the rings (see chapter "Replacing the pistons"). Simultaneous replacement of piston rings and pistons dramatically reduces oil consumption.
When replacing only piston rings without replacing pistons, remove carbon deposits from the piston crowns, from the annular grooves in the piston head and from the oil drain holes located in the grooves for the oil scraper rings. Remove carbon deposits from grooves carefully so as not to damage their side surfaces using the tool ().
Remove carbon deposits from oil drain holes with a 3 mm drill.
When using new or re-sized cylinder liners, the upper compression ring must be chrome plated and the remaining rings are tinned or phosphated. If the liner is not repaired, but only the piston rings are changed, then all of them must be tinned or phosphated, since the chrome ring is very badly worn in to the worn liner.
Before installing the pistons in the cylinders, spread the joints of the piston rings at an angle of 120 ° to each other.
After changing the piston rings, do not exceed the speed of 45-50 km / h on the vehicle within 1000 km of run.
Replacing pistons
Replace the pistons when the groove of the upper piston ring or the piston skirt is worn.
In partially worn cylinders, install pistons of the same size (nominal or overhaul) as pistons previously operated in this engine... However, it is advisable to pick up a kit bigger size pistons to reduce the clearance between the piston skirt and the cylinder bore.
In this case, check the clearance between the piston skirt and the cylinder bore in the lower, least worn part of the cylinder.
Do not suppose that the clearance in this part of the cylinder is less than 0.02 mm.
Spare parts are supplied with pistons with piston pins and retaining rings matched to them (see).
For selection, pistons of nominal size are sorted according to the outer diameter of the skirt. On the piston crowns, the letter designations of the size group are stamped, which are indicated in
The size of their diameter is also knocked out on the pistons of overhaul dimensions.
In addition to the selection of pistons for the cylinder liners according to the diameter of the skirt, they are also selected by weight. The difference in weight between the lightest and the heaviest piston for one engine must not exceed 4 g.
When assembling, install the pistons in the sleeves of the same group.
When installing pistons in cylinders, the "front" mark, cast on the piston, must face the front of the engine, on the split-skirt piston, the "back" mark - towards the clutch housing.
On all pistons with oversized dimensions, holes in the piston pin bosses are made of the nominal size with a breakdown into groups. If necessary, these holes are bored or reamed to the nearest repair dimension with a tolerance of –0.005 –0.015 mm. Taper and ovality of the hole - no more than 0.0025 mm. When machining, ensure that the axis of the hole is perpendicular to the axis of the piston, the permissible deviation is no more than 0.04 mm over a length of 100 mm.
Repair of connecting rods
Repair of connecting rods is reduced to replacing the bushing of the upper head and its subsequent processing under a piston pin of the nominal size or to processing the bushing available in the connecting rod for a pin of overhaul size.
The spare parts are supplied with bushings of the same size, made of 1 mm thick OTsS4-4-2.5 bronze tape.
When pressing a new bushing into the connecting rod, ensure that the hole in the bushing aligns with the hole in the upper connecting rod head.
The holes are used to supply lubricant to the piston pin.
After pressing in the bushing, seal its inner surface with a smooth broach to a diameter of 24.3 + 0.045 mm, and then unfold or bore to the nominal or repair size with a tolerance of +0.007 –0.003 mm.
For example, unfold or bore the bushing under a pin of a nominal size to a diameter of 25 +0.007 –0.003 mm or under a pin of an oversized size to a diameter of 25.20 +0.07 –0.003 mm.
The distance between the axes of the holes of the lower and upper connecting rod heads should be (168 ± 0.05) mm [(175 ± 0.05) mm for engines of model 4218]; the permissible non-parallelism of the axes in two mutually perpendicular planes over a length of 100 mm should be no more than 0.04 mm; ovality and taper should not exceed 0.005 mm. To maintain the specified dimensions and tolerances, unfold the upper connecting rod bushing in the jig.
After deployment, finish the hole on a special grinding head, holding the connecting rod in your hands (). Set the grinding stones of the head with a micrometer screw to the required overhaul dimension.
Connecting rods, the holes for the inserts in the lower head of which have an ovality of more than 0.05 mm, must be replaced.
Replacement and repair of piston pins
To replace the piston pins without pre-machining the holes in the piston and in the upper connecting rod head, piston pins increased in diameter by 0.08 mm are used. The use of pins enlarged by 0.12 mm and 0.20 mm requires pre-machining of the holes in the piston bosses and in the upper connecting rod head as described above (see chapters "Replacing pistons" and "Repairing connecting rods").
Before pressing out the gudgeon pin, remove the gudgeon pin circlips from the piston with pliers as shown. Press out and press in the pin on the tool, as shown on. Before pressing out the pin, heat the piston in hot water to 70 ° C.
Repair of piston pins consists in regrinding them from large repair sizes to smaller ones or in chrome plating, followed by processing to a nominal or repair size.
Fingers that have kinks, chipping and cracks of any size and location, as well as traces of overheating (tarnishing color) cannot be repaired.
Assembling the connecting rod-piston group
Select the piston pin to the upper connecting rod head with a clearance of 0.0045–0.0095 mm. At normal room temperature, the finger should slide smoothly in the bore of the upper crank arm with the force of the thumb (). The piston pin should be lightly greased with lightweight oil.
Install the pin into the piston with an interference fit of 0.0025–0.0075 mm.
In practice, the piston pin is selected in such a way that at normal room temperature (20 ° C) it would not enter the piston by hand force, and when the piston is heated in hot water to a temperature of 70 ° C it would enter it freely. Therefore, before assembling the piston, heat it in hot water to 70 ° C. Pressing in the pin without preheating the piston will damage the surface of the holes in the piston bosses, as well as deform the piston itself. Assemble the connecting rod-piston group using the same tool as disassembly (see).
To ensure correct engine balancing, the difference in weight between pistons and connecting rods installed in the engine must not exceed 8 g.
The gudgeon pin circlips should fit slightly in their grooves. Do not use used rings.
Fit the piston rings to the piston as described in the chapter "Replacing the piston rings".
Considering the complexity of the selection of the piston pin to the piston and connecting rod (to ensure nominal fits), pistons are supplied as spare parts assembled with a piston pin, retaining and piston rings.
Crankshaft repair
Repair of the crankshaft consists in regrinding the main and connecting rod journals to the next repair size.
The repair dimensions of the connecting rod and main journals are determined by the dimensions of the connecting rod and main bearing kits supplied in the spare parts, which are given in
The radial clearances in the connecting rod and main bearings of the crankshaft should be 0.020–0.049 mm and 0.020–0.066 mm, respectively. Re-grind the necks with a tolerance of 0.013 mm.
If the dimensions of the connecting rod and main journals do not coincide with each other, they must be re-grinded to the same repair size.
The chamfers and holes of the front and rear ends of the crankshaft are not suitable for installation in a grinding machine. To do this, make removable glass centers. Press the front center onto the neck with a diameter of 38 mm, and center the rear center on the outer diameter of the flange (Ж122 mm) of the shaft and fasten to it with bolts. When making transition centers, ensure that the centering and locating holes are concentric. Without observing this condition, it is impossible to ensure the necessary concentricity of the seats of the flywheel and gear to the axes of the main journals.
When grinding the connecting rod journals, install the shaft on additional centers coaxial with the connecting rod journal axes. To do this, you can use the centers-cups, providing them with flanges with two additional center holes, spaced from the middle hole by 46 ± 0.05 mm.
For the front end, it is better to make a new center-flange, which is installed on a neck with a diameter of 40 mm (on a key) and additionally secured with a bolt (ratchet) screwed into a threaded hole.
Before grinding the necks, deepen the chamfers on the edges of the oil channels so that their width after removing the entire allowance for grinding is 0.8–1.2 mm. Do this with an emery stone with a 60–90 ° apex angle driven by an electric drill.
When grinding the connecting rod journals, do not touch the side surfaces of the journals with the grinding wheel so as not to disturb the axial play of the connecting rods. Maintain the radius of transition to the lateral surface 3.5 mm. Grind with plenty of emulsion cooling.
During the regrinding process, observe:
1. The distance between the axes of the main and connecting rod journals is 46 ± 0.05 mm.
2. Taper, barrel, saddle, ovality and neck cut not more than 0.005 mm.
3. Angular arrangement of connecting rod journals ± 0 ° 10 ".
4. The non-parallelism of the connecting rod journal axes with the main journal axis is not more than 0.012 mm over the entire length of the connecting rod journal.
5. Runout (when installing the shaft with extreme main journals on prisms) of the middle main journals is not more than 0.02 mm, journals for the camshaft gear up to 0.03 mm, and journals for the pulley hub and rear oil seal up to 0.04 mm.
After grinding the journals, flush the crankshaft, and clean the oil channels from abrasive and resinous deposits. Unscrew the dirt trap plugs. After cleaning the dirt traps and channels, screw the plugs back into place and secure each of them against spontaneous twisting.
Clean the oil passages also during maintenance repairs of the engine, when the crankshaft is removed from the block.
After repair, re-assemble the crankshaft with the same flywheel and clutch that were in place before the repair. Install the clutch on the flywheel according to the factory marks "O", printed on both parts, one against the other near one of the bolts securing the clutch cover to the flywheel ().
Dynamically balance the crankshaft with clutch assembly on a special machine before installing the clutch assembly on the engine. Pre-center the clutch disc using the gearbox shaft or a special mandrel.
Eliminate imbalance by drilling metal in the flywheel rim at a radius of 158 mm with a 12 mm drill. The drilling depth should not exceed 12 mm. The permissible imbalance is not more than 70 gf cm.
Replacing the crankshaft main and connecting rod bearings
The spare parts are supplied with shells of main and connecting rod bearings of nominal and seven overhaul sizes, which are given in. Repair size inserts differ from nominal size inserts with an inner diameter reduced by 0.05; 0.25; 0.50; 0.75; 1.0; 1.25 and 1.50 mm.
Replace main and connecting rod bearing shells without any adjustment.
Depending on the wear of the journals, when changing the liners for the first time, use liners of the nominal or, in extreme cases, the first repair size (reduced by 0.05 mm).
Install the liners of the second and subsequent overhaul sizes into the engine only after regrinding the crankshaft journals.
If, as a result of repeated regrinding, the diameters of the crankshaft journals are reduced so much that the liners of the last repair size are unsuitable for it, then assemble the engine with a new shaft.
The radial clearance in the connecting rod and main bearings of the crankshaft should be 0.020–0.049 mm and 0.020–0.066 mm, respectively.
Check the magnitude of the radial clearances using a set of control probes made of copper foil 0.025 thick; 0.05; 0.075 and 0.1 mm, cut into strips 6–7 mm wide and slightly shorter than the liner width. The edges of the probes should be cleaned to prevent damage to the liner surface.
Check the radial clearance in the following order:
1. Remove the cap with the liner from the neck to be checked and place a pre-oiled 0.025 mm dipstick across the liner.
2. Reinstall the cover with insert and tighten with the bolts, while the bolts of the remaining covers must be loosened.
3. Rotate the crankshaft by hand through an angle of no more than 60–90 ° to avoid damaging the liner surface with the feeler gauge.
If the shaft turns too easily, then the clearance is greater than 0.025 mm. In this case, repeat the check with the 0.05 probes; 0.075 mm, etc. until it becomes impossible to turn the crankshaft.
The thickness of the stylus, at which the shaft turns with a noticeable effort, is considered equal to the actual clearance between the liner and the crankshaft journal.
Observe the following when replacing earbuds:
1. Replace liners without adjusting operations.
2. Make sure that the locking lugs at the joints of the liners freely (with the help of hand force) enter the grooves in the shaft beds.
3. At the same time as replacing the bearing shells, clean the dirt traps in the connecting rod journals.
The connecting rod bushings can be replaced without removing the engine from the vehicle chassis. Replace the main bearing shells with the engine removed from the vehicle chassis.
After replacing the liners, run the engine in as described in the "Engine Break-In After Repair" section.
If, when replacing the liners, the engine was not removed from the car, then during the first 1000 km of run the speed should not exceed 50 km / h.
Simultaneously with replacing the liners, check the axial clearance in the thrust bearing of the crankshaft, which should be 0.075–0.175 mm. If the axial clearance is more than 0.175 mm, replace washers 7 () and 8 with new ones. The front washer is made in four thicknesses: 2.350–2.375; 2.375-2.400; 2,400-2,425; 2.425-2.450 mm.
To check the thrust bearing clearance, place a screwdriver () between the first crank of the shaft and the front wall of the block and press the shaft towards the rear end of the motor. Then, with a feeler gauge, determine the clearance between the end face of the thrust bearing rear washer and the shoulder plane of the first main journal.
Before installing the liners, check the alignment of the crankshaft main journals (deflection boom). To do this, place the crankshaft in the centers and check the position of the axles of the main journals according to the indicator readings.
Repair of the camshaft and replacement of its bushings
Restore the required gaps in the camshaft bushings by regrinding the bearing journals, reducing their size by no more than 0.75 mm, and replacing the worn out bushings with semi-finished ones, followed by their boring to the size of the regrind journals.
On engines without bushings, restore the required clearances by boring holes in the block for bushings, guided by the data. (and), and subsequent pressing in of bushings of nominal or repair size.
Before regrinding the camshaft journals, deepen the grooves on the first and last journals by the amount of the reduction in the diameter of these journals in order to ensure that after regrinding the journals, the lubricant flows to the timing gears and to the rocker arm axis. Grind the necks in the centers with a tolerance of 0.02 mm. After polishing the neck, polish it.
It is more convenient to press-out and press-in bushings using threaded rods (of appropriate length) with nuts and washers.
Semi-machined camshaft bushings, supplied as a single engine kit, have the same outer diameter as nominal bushings, so they are pressed into the block bores without pretreating.
To ensure a sufficient thickness of the babbitt layer (antifriction material), the repair reduction of the inner diameter of all bushings must be the same.
When pressing in the bushings, make sure that their side holes coincide with the oil channels in the block. Boring the bushings, reducing the diameter of each subsequent bushing, starting from the front end of the block, by 1 mm. Bore with a tolerance of +0.050 +0.025 mm so that the clearances in the bushings after installing the shaft correspond to the data
When boring bushings and holes in the bushing block, keep the distance between the axes of the bore holes and camshaft s (118 ± 0.025) mm. Check this dimension at the front end of the block. The deviation from the alignment of the holes in the bushings should be no more than 0.04 mm, and the deviation from the parallelism of the crankshaft and camshafts should be no more than 0.04 mm along the entire length of the block. To ensure the alignment of the bushings within the specified limits, process them simultaneously using a long and sufficiently rigid boring bar with cutters or reamers attached to it according to the number of supports. Install the boring bar based on the main bearing shell holes.
With slight wear and tear, clean the camshaft cams with abrasive paper: first coarse, then fine. In this case, the sandpaper should cover at least half of the cam profile and have some tension, which will ensure the least distortion of the cam profile.
If the cams are worn in height by more than 0.5 mm, replace the camshaft with a new one.
Check the camshaft curvature with an indicator on the backs of the heads (on the cylindrical surface) of the intake and exhaust cams of the second and third cylinders. At the same time, install the shaft in the centers. If the shaft runout exceeds 0.03 mm, then straighten or replace the shaft.
Restoration of valve tightness and replacement of valve sleeves
Violation of valve tightness when correct clearances between the valve stems and rocker arms, as well as when the carburetor and the ignition system are working properly, it is detected by the characteristic pops from the muffler and carburetor. At the same time, the engine runs intermittently and does not develop full power.
Restore the tightness of the valves by lapping the working chamfers of the valves to their seats. If there are shells on the working chamfers and seats, annular workings or scratches that cannot be removed by lapping, grind the chamfers, followed by lapping the valves to the seats. Replace warped-head valves.
Grind the valve chamfers with a pneumatic or electric drill model 2213, 2447 GARO or manually using a rotary wheel. Perform lapping in a back-and-forth motion, in which the valve turns slightly more in one direction than in the other. When lapping under the valve, install a release spring with a slight elasticity. The inner diameter of the spring should be about 10 mm. The spring should lift the valve slightly above the seat, and when pressed lightly, the valve should sit on the seat. The connection between the instrument and the valve is carried out by a rubber suction device, as shown in. For better adhesion of the suction cup to the valve, their surfaces must be dry and clean.
To speed up the lapping, use a lapping paste made up of one part of M20 micro-powder and two parts of engine oil. Stir the mixture thoroughly before use. Lapping until a uniform matte chamfer appears on the working surfaces of the seat and valve disc around the entire circumference. At the end of lapping, reduce the amount of micro-powder in the lapping paste. Finish lapping in one clean oil. Instead of lapping paste, you can use # 00 emery powder mixed with engine oil.
For grinding the working chamfers of the valves, it is recommended to use grinding machines type R-108 or OPR-1841 GARO. At the same time, clamp the valve stem in the centering chuck of the headstock, installed at an angle of 44 ° 30 "to the working surface of the grinding stone. A 30" decrease in the angle of inclination of the working chamfer of the valve head compared to the chamfer angle of the seats accelerates the running-in and improves the tightness of the valves. When grinding, bevel off the valve head with a minimum amount of metal. The height of the cylindrical shoulder of the working chamfer of the valve head after grinding should be at least 0.7 mm, and the alignment of the working chamfer relative to the rod within 0.03 mm of the total indicator readings. Valve stem runout - no more than 0.02 mm. Replace valves with large runout with new ones. Do not re-grind valve stems to a smaller size, as there will be a need to make new valve spring plate crackers.
Grind the seat chamfers at a 45 ° angle coaxial with the bore in the bushing. The chamfer width should be 1.6–2.4 mm. It is recommended to use the tool shown on the right for grinding the seats. Grind the saddle without lapping paste or oil until the stone is covering the entire working surface.
Change the stone to a fine-grained one after coarse finishing and fine-sand the seat. The runout of the chamfer relative to the axis of the bore of the valve sleeve should not exceed 0.03 mm. Replace worn seats with new ones. Spare parts are supplied with valve seats with an outer diameter greater than the nominal by 0.25 mm. Remove worn seats from the head using a countersink.
After removing the seats, bore in the head of the socket for the outlet valve to a diameter of 38.75 + 0.025 mm and for the inlet valve to a diameter of 49.25 + 0.25 mm. Before pressing the seats, heat the cylinder head to a temperature of 170 ° C, and cool the seats with dry ice. Press in quickly, without allowing the seats to heat up. The cooled head tightly wraps around the saddles. To increase the seating strength of the seats, hammer the OD with a flat mandrel to fill the seat chamfer. Then grind to the required size and grind.
If the wear of the valve stem and guide sleeve is so great that the clearance in their joint exceeds 0.25 mm, then restore the valve tightness only after replacing the valve and its sleeve. Spare parts are supplied with valves of nominal sizes only, and guide bushings with an inner diameter reduced by 0.3 mm for their subsequent reaming to the final size after being pressed into the cylinder head.
Expand the pressed-in sleeves to a diameter of 9 + 0.022 mm. The inlet valve stem has a diameter of 9 –0.050 –0.075 mm, the diameter of the outlet valve 9 –0.075 –0.095 mm, therefore, the clearances between the inlet and outlet valve stems and bushings should be equal to 0.050–0.097 mm and 0.075–0.117 mm, respectively.
Press out the worn guide bushings from the cylinder head using a punch shown in fig. ...
Press in the new bushing from the side of the rocker arms using the same punch until it stops in the retaining ring on the bushing. In this case, as in the case of pressing in the valve seats, heat the cylinder head to a temperature of 170 ° C, and cool the sleeve with dry ice.
After replacing the valve bushings, grind the seats (centering on the holes in the bushings) and then grind the valves to them. After grinding the seats and lapping in the valves, thoroughly rinse all channels and places where abrasive could get into and blow with compressed air.
Valve sleeves are porous sintered metal. Soak them in oil after finishing and rinsing. To do this, insert a felt wick soaked in spindle oil into each sleeve for several hours. Before assembling, lubricate the valve stems with a thin layer of a mixture prepared from seven parts of an oil colloidal graphite preparation and three parts of engine oil.
Replacing valve springs
Possible valve springs failures that appear during operation may be: a decrease in elasticity, breakage or cracks on the turns.
Check the elasticity of the valve springs during disassembly. valve train... The force required to compress the new valve spring up to 46 mm in height should be 267-310 N (27.3-31.7 kgf), and up to 37 mm - 686-784 N (70-80 kgf). If the compression force of the spring up to 46 mm in height is less than 235 N (24 kgf), and up to 37 mm is less than 558.6 N
(57 kgf), then replace such a spring with a new one.
Replace springs with breakage, cracks and traces of corrosion with new ones.
Replacement of pushers
The pilot holes in the block for the pushers are slightly worn out, therefore, restore the nominal clearance in this mating by replacing the worn pushers with new ones. Only the nominal size pushers are supplied with spare parts.
Match the pushers to the holes with a gap of 0.040–0.015 mm. Pushers, depending on the size of the outer diameter, are divided into two groups and are marked with stamping: number 1 - with a pusher diameter of 25 –0.008 –0.015 mm and number 2 - with a pusher diameter
25 –0.015 –0.022 mm. Correctly selected pusher, lubricated with liquid mineral oil, should smoothly descend under its own weight into the block socket and turn easily in it.
Replace pushers with radial scuffs, wear or chipping of the working surface at the ends of the plates.
Distributor drive repair
|
Rice. 2.62. The drive of the oil pump and the ignition distributor: the position of the groove of the roller A - on the drive installed on the engine; B - on the drive before installing it on the engine; B - on the oil pump shaft before installing the drive on the engine; 1 - oil pump roller; 2 - bushing; 3 - intermediate roller; 4 - pin; 5 - drive gear; 6 - camshaft gear; 7 - thrust washer; 8 - block of cylinders; 9 - gasket; 10 - drive roller; 11 - drive body; 12 - ignition distributor drive |
The roller 10 () of the distributor drive worn out in diameter is restored by chrome plating followed by grinding to a diameter of 13–0.011 mm.
Replace the pinion gear 5 of the distributor drive, which has breaks, staining or significant wear of the surface of the teeth, as well as wear of the pin hole to a size of more than 4.2 mm, with a new one.
To replace the roller or the distributor drive gear, remove the gear from the roller by first removing the pin of the gear using a 3 mm diameter bit. When removing the gear from the roller, place the drive housing 11 with its upper end on a support with a hole in it for the passage of the drive roller assembly with a thrust bushing.
Assemble the drive taking into account the following:
1. When installing the roller (assembled with the thrust bush) in the distributor drive housing, lubricate the roller with engine oil.
2. Having connected the drive shaft 10 with the intermediate drive plate 3 of the drive and putting on the thrust washer 7, press the gear onto the roller, maintaining a gap between thrust washer and drive gear 0.25 –0.15 –0.10 mm ().
In this case, it is necessary that the O – O axis passing through the middle of the depressions between the two teeth on the end B was displaced relative to the B – C axis of the roller spline by 5 ° 30 "± 1.
3. Drill a hole in the pinion and pin roller with a diameter of (4 ± 0.037) mm, maintaining the distance from the axis of the hole to the end of the pinion (18.8 ± 0.15) mm.
When drilling a hole and when setting the gap between the thrust washer and the gear, the distributor drive shaft assembly with the thrust sleeve must be pressed against the drive housing in the direction of the oil pump. The pin connecting the pinion to the pinion should be 4–0.025 mm in diameter and 22 mm long.
In the assembled distributor drive, its roller should be free to rotate by hand.
Oil pump repair
With heavy wear of the oil pump parts, the pressure in the lubrication system decreases and noise appears. When disassembling the pump, check the spring tension pressure reducing valve... The elasticity of the spring is considered sufficient if a force (54 ± 2.45) N [(5.5 ± 0.25) kgf] is required to compress it up to 24 mm in height.
Repairing an oil pump usually consists of grinding the end caps, replacing gears and gaskets.
When disassembling the pump, pre-drill the riveted head of the bushing fixing pin 2 (see) on its roller 1, knock out the pin, remove the bushing and the pump cover. After that, remove the pump shaft together with the drive gear from the housing towards its cover.
In the case of disassembling the pinion gear and roller, drill the pin with a 3 mm drill.
Replace the drive and driven gears with chipped teeth, as well as with noticeable deformations of the surface of the teeth with new ones. Installed in the pump housing, the drive and driven gears should be easily turned by hand by the drive shaft.
If there is a significant (more than 0.05 mm) depletion from the ends of the gears on the inner plane of the cover, grind it.
Paronite gaskets 0.3–0.4 mm thick are installed between the cover, plate and pump casing.
The use of shellac, paint or other sealing substances when installing the gasket, or installing a thicker gasket, is not allowed, as this will reduce the pump flow.
Assemble the pump taking into account the following:
1. Press the bushing onto the drive shaft, making sure that the distance between the end of the drive shaft and the end of the sleeve is 8 mm (). In this case, the gap between the pump casing and the other end of the sleeve must be at least 0.5 mm.
2. Drill in the drive roller
and in the sleeve a hole with a diameter
4 + 0.03–0.05 mm, keeping the dimension (20 ± 0.25) mm.
3. Countersink the hole on both sides to a depth of 0.5 mm at an angle of 90 °, press in a pin with a diameter of 4-0.048 mm and a length of 19 mm and rivet it on both sides.
If it is impossible to restore the pump performance by repair, then replace it with a new one.
Install the oil pump drive and ignition distributor on the block in the following order:
1. Remove the spark plug from the first cylinder.
2. Install a compressor in the hole for the spark plug and turn the crankshaft with the starting handle until the arrow starts moving. This will happen at the beginning of the compression stroke in the first cylinder. You can plug the candle hole with a paper wad or your thumb. In this case, during the compression stroke, a wad will pop out or air will be felt from under the finger.
3. After making sure that compression has started, carefully rotate the crankshaft until the hole on the crankshaft pulley rim aligns with the pointer (pin) on the timing gear cover.
4. Turn the drive shaft so that the slot on its end for the distributor awl is positioned as indicated in B, and using a screwdriver, turn the oil pump shaft to the position indicated in C.
5. Carefully, without touching the gear wheels on the block walls, insert the drive into the block. Once the drive is in place, the roller should be in the position shown in A.
To reduce wear on the drive pivots, align the pump with the drive bore. To do this, use a mandrel () that fits snugly into the drive bore in the block and has a 13 mm diameter cylindrical shank. Center the pump on the arbor shank and secure in this position.
Cooling pump repair
|
Rice. 2.66. Engine cooling system pump: a - cooling system pump 21-1307010-52; b - cooling system pump 421-1307010-01; 1 - nut; 2 - roller; 3 - pump casing; 4 - control hole for the lubricant outlet; 5 - press lubricator; 6 - spacer sleeve; 7 - sealing washer; 8 - rubber cuff; 9 - spring; 10 - impeller; 11 - impeller mounting bolt; 12 - retaining ring; 13 - bearings; 14 - fan pulley hub; 15 - belt; 16 - pulley; 17 - fan; 18 - bolt; 19 - roller-ball bearing assembled with a roller; 20 - retainer; 21 - stuffing box; 22 - pump casing cover |
Possible pump malfunctions () may be: fluid flow through the impeller oil seal as a result of wear of the sealing washer or destruction of the rubber seal of the oil seal, wear of bearings, breakage and cracks of the impeller.
Repair of the pump 21–1307010–52 of the cooling system
Eliminate fluid leakage from the pump by replacing the sealing washer and rubber cuff. To replace, remove the pump from the engine, disconnect it from the bracket, remove the impeller () with special tool 71-1769, remove the sealing washer and the gland seal.
To assemble the impeller seal, first insert the rubber seal assembly into the seal holder located on the pump housing, then the sealing washer and retaining ring. In this case, lubricate the part of the pump shaft, coupled with the rubber cuff, with soap before installing the oil seal and pressing the impeller, and the end of the impeller, which is in contact with the sealing washer, with a thin layer of graphite grease.
Before installing the gland, check its end (the end of the sealing washer) for paint: when the gland is compressed to a height of 13 mm, the end imprint should have at least two completely closed circles without breaks.
Press the impeller onto the roller on a hand press until its hub stops against the flat end. In this case, the pump should rest on the table with the front end of the roller, and the force should be applied to the impeller hub.
To replace the bearings or pump shaft, disassemble the pump completely in the following order:
1. Remove the impeller from the pump shaft and remove the sealing washer and rubber collar.
|
Rice. 2.68. Removing the pump pulley hub |
2. Unscrew the pulley hub retaining nut and remove it using the tool as shown.
3. Remove the bearing retaining ring from the pump housing 1 () and press out or knock out the roller 2 with the bearings from the housing with a copper hammer using a press, resting the front end of the housing on the support 3 with a hole for the passage of the bearings.
We assemble the pump in the reverse order. At the same time, press the new bearing onto the roller 1 () and into the housing 2 at the same time using a hand press and a mandrel 3. The felt bearing gland must face the retaining ring. Putting the spacer sleeve on the shaft, press the second bearing out with the felt gland.
After replacing the retaining ring, press the pulley hub onto the front end of the roller, resting the roller against the rear end of the ring. Press the pulley hub onto the pump shaft of the 4218 engine after installing the retainer 19 (see, b). When pressing on the hub, make sure there is no play between the bearing and the circlip.
Rice. 2.66, b). Press out the oil seal.
Assemble the pump in reverse order. In this case, press-in the fan pulley hub until it stops in the shoulder, and press-in the impeller - to the size 117.4 +0.925 –1.035 (see, b).
Before assembly, lubricate the part of the roller of the roller-ball bearing, mated with the oil seal, with soap, and the end of the impeller, which is in contact with the oil seal, with graphite grease.
When installing the assembled pump on the motor, pay attention to the suitability of a paronite gasket between the cover and the pump housing.
Repair of fuel tanks
A possible malfunction of the tanks can be a leakage due to the formation of cracks, holes or other damage that occurs during operation. For repair, remove the tank from the car, clean it from dirt and rinse the outside.
To identify a malfunction, immerse the tank in a bath of water and supply compressed air inside the tank at a pressure of 30 kPa (0.3 kgf / cm2). All tank openings must be pre-sealed. In places where the tightness is broken, air bubbles will come out of the tank. Mark all damage with paint.
Then disassemble the tank completely, thoroughly rinse it from the inside with hot water to remove gasoline vapors and blow it with compressed air. Solder small cracks with soft solder. Apply metal patches to large cracks and holes. It is possible to seal cracks with epoxy pastes and layered fiberglass patches. After repair, test the tank for leaks.
Repair small cracks in the cork fuel tank caused by impacts. Seal cracks with epoxy paste. After the paste has hardened, check the function of the plug valves.
Repair fuel pump
Possible pump malfunctions can be: violation of the tightness of the diaphragm and valves, reduced elasticity or breakdown of the diaphragm spring, wear of pump drive parts.
To disassemble the pump, remove the head cover 10 (see) from it, the gasket 9 and the filter 8. Then unscrew the screws securing the head 14 of the housing, separate the head from the diaphragm.
When removing the casing head, be careful not to damage the diaphragm as the diaphragm sticks to the flanges of the pump head and casing. Next, disassemble the drive mechanism, for which first press out the axle 19 of the drive levers and remove the lever 17 and spring 16. Carefully release the diaphragm 6 and remove it and the spring 5 and the seal 3 with the washer 4.
Disassembling the head, remove the inlet 7 and discharge valves. To do this, press out the valve cages.
Rice. 2.73. Position of the fuel pump head when installing it
When installing the pump head B9V-B, its position relative to the body must correspond. Tighten the head fastening screws with the diaphragm pulled to the lowest position using the manual priming lever.
This assembly provides the necessary sagging of the diaphragm and relieves it of excessive tensile forces, leading to a sharp reduction in the durability of the diaphragm. After assembly, check the pump on the model 527B or 577B GARO.
At a camshaft rotational speed of 120 min – 1 and a suction height of 400 mm, the pump must ensure the start of fuel delivery no later than 22 s after switching on, create a pressure of 150–210 mm Hg. Art. and a vacuum of at least 350 mm Hg. Art. The pressure and vacuum generated by the pump must be maintained within the specified limits with the drive off for 10 s.
The pump flow at a camshaft speed of 1800 min – 1 must be at least 120 l / h. If no dedicated pump tester is available, it can be tested directly on the engine as described in the Maintenance section.
Carburetor repair
Carry out repair of the carburetor in case of breakage of any of its parts or in case of unsatisfactory operation of the carburetor after adjustment in all engine operating modes.
Before disassembling, wash the carburetor with kerosene to remove dust and dirt. When working on leaded gasoline, soak the carburetor in kerosene for 10–20 minutes.
The order of disassembly and assembly of the carburetor K-131
Remove the five screws securing the float chamber cover. Carefully lifting the cover so as not to damage the float mechanism, disconnect the low speed rod, remove the cover and the float chamber gasket.
Turn the cover over and, holding the float, remove the float shaft from the struts. Remove the float and carefully remove the needle with the polyurethane sealing washer from the fuel supply valve body. Unscrew the valve body and remove its gasket. Unscrew the filter plug, remove its gasket and take out the filter screen. Unscrew the accelerator pump sprayer and remove the sealing washer.
Disassemble the air damper drive mechanism and remove the damper only if the mechanism operates unsatisfactorily, and also if the gaps between the wall of the air pipe and the damper when it is closed exceed 0.2 mm.
Separate the mixing chamber from the body of the float chamber, for which unscrew the two bolts and, having unpinned the shackle of the accelerating pump drive, remove it from the rod and the lever.
Remove the mixing chamber gasket and remove the large diffuser from the float chamber housing.
Remove the accelerator pump piston assembly with its drive parts and economizer drive rod. Unscrew the economizer valve assembly and remove it from the well. Unscrew the cap of the well of the emulsion tube together with the gasket and remove this tube, unscrew the air nozzle idle move.
Unscrew the plugs of the fuel and air nozzles of the main metering system and the fuel idle jet, remove the gaskets of these plugs and unscrew the corresponding jets.
Remove the booster pump valve lock and remove the valve from the well.
Remove the retaining ring and the accelerator pump check valve ball.
Do not press out the small diffuser unnecessarily.
When disassembling the mixing chamber, unscrew the screw for adjusting the quality of the idle mixture and remove its spring.
Remove the throttle valve and its axis only if:
- the throttle valve shaft does not rotate freely in the chamber bosses;
- the gaps between the walls of the chamber and the shutter in the closed position are more than 0.06 mm;
- the upper edge of the throttle valve in the closed position does not coincide with the axis of the transition hole Ж 1.6 + 0.06 mm (a deviation of ± 0.15 mm is allowed).
After disassembling, wash all carburetor parts in unleaded gasoline or hot water with a temperature of at least 80 ° C, then blow with compressed air.
All carburetor parts must be clean, free from carbon deposits and tarry deposits.
Nozzles and other dispensing elements must be of the specified flow rate or dimensions.
The economizer valve assembly must be tight. When checking its tightness under a pressure of 1200 mm of water. Art. a flow of no more than four drops of water per minute is allowed.
The degree of wear of the piston of the accelerating pump and the walls of its well, as well as the tightness of the check valve, must be such as to ensure that the pump is supplied at least 8 cm3 in 10 piston strokes.
Check the float for leaks by immersing it in water with a temperature of at least 80 ° C. The release of bubbles from the float indicates a violation of its tightness.
Seal the damaged areas of the float with soft solder, having previously removed the fuel that has got into the float.
After soldering, check the weight of the float, which should be equal to (13.3 ± 0.7) g. Adjust the weight by removing excess solder without damaging the tightness of the float.
The surface of the housing connector and the float chamber cover must be flat, the permissible deviation from the plane is no more than 0.2 mm.
Assemble the carburetor in the reverse order of disassembly, taking into account the following:
1. If during disassembly the throttle or air dampers were removed, then during assembly, tighten the screws for their fastening.
2. Check that the economizer is fully engaged and, if necessary, adjust as described in the chapter "Maintaining the power system".
Rice. 2.29. Carburetor K – 151V: 1 - air damper; 2 - screw; 3 - starting spring; 4 - carburetor cover; 5 - bracket (only for К-151Н); 6 - gasket; 7 - diaphragm of the pneumatic corrector with draft assembly; 8 - gasket; 9 - pneumatic corrector cover; 10 - spring; 11 - screw; 12 - screw-displacer; 13 - ball (inlet valve); 14 - float; 15 - body of the float chamber; 16 - fuel supply union; 17 - washer; 18 - fuel filter; 19 - washer; 20 - fuel-conducting bolt; 21 - cork; 22 - cover of the accelerating pump; 23 - accelerator pump drive lever; 24 - fitting for ventilation of crankcase gases; 25 - secondary chamber throttle valve; 26 - housing of mixing chambers; 27 - screw; 28 - cam; 29 - screw; 30 - throttle damper of the primary chamber; 31 - economizer valve assembly; 32 - screw for adjusting the composition of the mixture; 33 - shut-off element of the EPHH valve; 34 - valve body EPHH; 35 - gasket; 36 - EPHH valve cover; 37 - tube; 38 - screw for operational adjustment of idle speed; 39 - heat-insulating gasket (textolite); 40 - heat-insulating gasket (cardboard); 41 - small diffuser; 42 - accelerator pump sprayer;
5. Unscrew the adjusting screw 43 of the fuel bypass, turn the body of the float chamber 15 over until the ball 13 of the inlet valve falls out.
6. Unscrew the displacement screw 12.
7. Unscrew the cylindrical plug and take out the float shaft, remove the float and take out the fuel valve. Unscrew the fuel valve seat together with the gasket.
8. Unscrew the fuel-supply bolt 20, remove the fuel inlet union 16 and fuel filter 18.
9. Unscrew the four screws 47 securing the accelerator pump cover, remove the cover 22, the gasket 46, the accelerator pump diaphragm assembly 45 and the spring 44.
10. Unscrew the detachable jets, pull out the emulsion tubes.
11. Unscrew the two screws 29 and detach the housing of the mixing chambers 16 from the body of the float chamber 15, taking care not to damage the cardboard 40 and textolite 39 gaskets.
12. Unscrew the two screws securing the EPCH valve assembly (pos. 31) and remove the latter from the mixing chambers body.
13. Unscrew the two screws securing the cover 36 of the EPCH valve, remove the cover 36, the cardboard gasket 35 and the body 34 of the EPCH valve.
To disassemble the K-151V carburetor, in addition to the above, do:
1. Unscrew the lock 53, disengage the rod 52 with the lever 55 and remove the lever 55.
2. Remove two screws 57, cover 58, valve 59, gasket 61 and spring 60.
Control and inspection of parts
All parts must be clean, free of carbon deposits and resinous deposits. The jets after flushing and blowing with compressed air must have the specified flow capacity. All valves must be tight, the gaskets must be intact and have traces (imprints) of the sealed surfaces. The diaphragms of the accelerating pump, pneumatic corrector and EPHH valve must be intact, without damage. Replace defective or damaged parts with new ones.
Assembling the carburetor
The carburetor should be assembled in the reverse order of disassembly. First you need to assemble all the carburetor body parts - the carburetor cover, the float chamber body and the mixing chamber body, and then connect them together.
Rice. 2.29), tighten the mentioned screws, screw the economizer valve assembly 31 to the mixing chambers body with two screws.
8. When assembling, do not mix up the jets.
9. Check the gap between the mixing chamber wall and the edge of the throttle valve when fully open. throttle primary chamber. The gap must be at least 14.5 mm. If necessary, provide clearance 1 by bending the lever stop.
The fact that the car needs to replace the piston rings, and not some others renovation work, the engine itself will tell. The signs of such a malfunction appear quite brightly, so it will be difficult not to notice them. But before talking about the symptoms, you need to understand what the rings are and what role they play in the engine.
What are piston rings, their purpose
Piston rings are elastic open-ended elements that are installed in special grooves on the piston body. They are made of steel or high-strength cast iron, and covered with an alloying material on top. The alloy coating further increases the strength and also reduces the wear rate.
Usually, 3 rings are inserted into the piston: 2 compression rings (occupy 2 upper grooves) and 1 oil scraper (lower groove). The purpose of the compression rings is to prevent hot gases from escaping along the piston into the crankcase. Oil scraper - removes excess oil from the cylinder bore, preventing it from entering the combustion chamber. In addition, the rings reduce the temperature of the piston by transferring almost half of the surface heat to the cylinder walls.
When the piston rings cease to cope with the tasks assigned to them, due to their wear, the car engine signals this by the manifestation of the corresponding symptoms.
Signs of wear on piston rings
The fact that wear has reached a critical stage is indicated by blue or black. This indicates that excess oil entered the combustion chamber past the oil scraper ring and burned there along with the fuel. Black smoke coming out of the crankcase ventilation tube indicates that the compression rings, due to wear, allow gases to break through from the combustion chamber into its cavity.
Critical wear is accompanied by a decrease in compression (ability to hold pressure) in the engine cylinders. This means that part of the gases formed during the combustion of the fuel mixture, which was supposed to push the piston, broke into the crankcase without doing any useful work. This will lead to a drop in cylinder pressure, therefore, the engine will lose some of its power. Observed.
A special device is a compressometer. When the nominal pressure values are unknown (there are no operating instructions), first it is measured in a dry cylinder, then a little engine oil is poured through the spark plug hole, and the measurement is done again. If the compression increases, then the rings need to be replaced. Similar signs can be observed in the case of their "occurrence".
"Stuck" occurs when carbon deposits formed in the piston grooves prevent the piston rings from springing, resulting in a decrease in their tightness to the cylinder surface.
Such a problem, if the case is not severely neglected, can be corrected with the help of special fuel additives. An engine with a carburetor system can be cleaned with a carbon remover spray that is injected directly into the carburetor. If removing carbon deposits from the combustion chamber did not give an effect, then there is only one way out - replacing the piston rings and cleaning the grooves.
How to replace piston rings yourself
Of course, replacing rings is a rather laborious procedure. It requires accuracy and certain skills, but by and large there is nothing complicated about it (if you do not remove the engine). For this you need:
![](https://i2.wp.com/autolirika.ru/wp-content/uploads/2016/03/image5979.png)
If the wear of the connecting rod bearings allows them to be reused, then it is not worth replacing, since this will require bore the crankshaft journals. Without experience, you cannot perform such work on your own.
Tools required for work
To replace the rings you will need:
- sets of open-end and spanner wrenches, as well as a wrench with an extension and heads with a nominal value of 10 - 19;
- torque wrench;
- specialist. crimp (mandrel).
In addition, you will need oil resistant. It will come in handy during the installation of the oil pan and valve cover gaskets.
And there seems to be nothing complicated in the actions listed above, if the replacement is made without removing the engine from the car. However, there are nuances, without which the engine with new rings will not work for a long time. When a cylinder reaches the limit of wear, a "step" forms on the surface of its mirror. Having hit against it, the new ring will either break immediately, or get a crack, which in the end will still lead to its breakage. In addition, the grooves of the old piston also have wear, so lapping the new rings to the cylinder will be difficult or even impossible. This means that it is better to entrust the troubleshooting of the piston group and cylinders to professionals.
Cylinder boring and honing should also be done by qualified personnel. In addition, this work cannot be performed without removing the engine. Therefore, before getting down to business, you should think carefully, really assess your strengths and capabilities. So that the result of the repair does not become the replacement of the piston group as a whole, or even worse, the engine would not have to be handed over to.
All parts of the connecting rod-piston group are divided into categories and selected individually to each other.
Tolerance group, indicated by a letter and embossed on the piston crown, ...
... must match the group indicated on the cylinder liner.
The values of the diameters of the holes in the piston bosses, the connecting rod head and the outer diameters of the piston pin are divided into groups, and are indicated by paint.
On the piston pin, the group is marked with paint applied to its end or inner surface. It must match the group ...
... indicated on the piston pin boss.
On the connecting rod, the piston pin hole group is also marked with paint. It must either match or be adjacent to the group's finger.
We check the correctness of the selection of the connecting rod and the piston pin in the following way.
The finger lubricated with engine oil should move in the connecting rod head under the force of the thumb, but not fall out of the bushing.
On the side surface of the lower connecting rod head and the cover there is a serial number of the cylinder in which it was installed.
The numbers on the connecting rod cover and on the connecting rod itself must match and be on the same side.
The connecting rods supplied in spare parts do not have such markings, therefore, before disassembling them, make the marking of the connecting rods and caps in the same way as the factory ones, so as not to turn over or confuse the caps during assembly.
We heat the piston to a temperature of 60-80 ° C. It is allowed to heat the piston in hot water.
We introduce the head of the connecting rod between the piston bosses ...
… And press in the piston pin greased with engine oil with a hammer through a mandrel or a tool.
We fix the piston pin on both sides with retaining rings.
ATTENTION
The protrusion on the connecting rod cover must be on the same side as the inscription ...
ATTENTION
... "FRONT" on the piston.
The liner seats are thoroughly cleaned of scale and corrosion.
Replace the sealing copper washers of the cylinder liners with new ones.
The sleeves are pressed in with light hammer blows through a wooden block.
With a set of probes, we check the protrusion of the sleeve above the plane of the block, which should be 0.02-0.10 mm.
We select the piston rings for the cylinders.
We install the rings one by one into the cylinder to a depth of 20-30 mm and measure the gaps with a feeler gauge. Compression rings should have a gap in the lock of 0.3-0.6 mm, oil scraper rings - 0.3-1.0 mm.
If piston replacement is not expected, check the groove width with new piston rings.
We check the clearance at several points around the circumference of the piston. The value of the side clearance for the compression rings should be 0.050-0.082 mm, for the assembled oil scraper ring 0.135-0.335 mm.
In worn-out cylinders, you can install rings of the nearest repair size and, if necessary, saw off the ends to obtain a gap of 0.3 mm.
We put the rings on the piston, starting with the oil scraper ring.
Having opened the lock of the oil scraper ring expander, we install it in the lower groove of the ring, after which we bring the ends of the expander.
We put the oil scraper ring on the expander ...
… Inscribed on the piston crown.
The angle between the expander and the ring locks is 45 degrees.
Installing the lower compression ring ...
… With an inscription and a chamfer on the inner side of the ring towards the piston crown.
Install the upper compression ring.
Size groups of pins, pistons and connecting rods