It may seem that there is nothing easier than preparing the car for the application of polishing compound, but this is not the case. The preparatory process before is rather difficult, the preparatory activities must be carried out carefully and in a certain sequence.
Before you need to do the following:
- Car wash.
- Pasting of plastic and rubber surfaces with masking tape.
- Car body cleaning from bituminous stains and silicone.
- Degreasing the surface.
- Processing with special clay.
- Pasting of openings and gaps of the car with adhesive tape.
Insofar as preparatory work before are very important, you should familiarize yourself with each step in detail. In addition, the information will be useful for ordinary motorists who sometimes like to wipe with a polish and a rag.
Are the cars boring and dirty? Then it's time for a thorough spring cleaning to clean the car. Here are ten tips on how to eliminate the traces of winter - so your car shines with a new shine. Snow and ice are rare in some, but the cold season still leaves its mark. it the best time for thorough cleaning of the car - both the body and the interior of the car. After spring cleaning, your car is not only clean, but also better protected from environmental influences.
Tip 1: Drive through a car wash or car wash
First of all, the worst dirt and possible salt residues. If you are using a cleaner high pressure for prewash, be sure to maintain the required minimum distance of 30 centimeters. Otherwise damage to sensitive electronics and electronics.
Tip 2: Hand wash as a gentle alternative
If you can spend a little time cleaning your cars, you should wash your car by hand with plenty of water, clean and soft sponges, and a mild detergent.It should be remembered that with poor-quality preparation paintwork may be damaged.
Car wash
Although abrasive clay will be used in the future, the surface of the car must still be thoroughly washed. In this case, it is recommended to use a non-contact washing system. Of course, this method is quick and does not damage the car body with minor scratches. If contactless system there is no sink at hand, then you can clean the surface with a hand wash. Hand washing is better because you can remove dirt even in the most remote places. This method is considered to be more effective.
Use only light pressure as dirt particles in the sponge can scratch the paint. Also pay attention to the compatibility of materials with the cleaning agent, most household items are unusable. Removable rubber gaskets should always be handled with extreme care.
Tip 3: Cleaning and Caring for Wheels
Don't forget the rims when cleaning the car. You must periodically remove dirt and brake deposits to prevent brake dust from being lost into the material over time and deteriorating the protective coating on the rims. A special rim cleaner helps with washing, the subsequent sealing of the rim protects against new deposits and makes the next cleaning easier.
In any case, even if the body is washed by a non-contact method, the surface still needs to be cleaned manually. For washing, it is better to use not special shampoos, but dishwashing detergent.
It should be diluted 1: 500. Thanks to this tool, the water will automatically act as a degreaser. To clean the surface, it is recommended to use a microfiber cloth instead of foam.
Tip 4: Repair minor scratches immediately
If the paint gives off a new shine after washing the car, you should look for the car body after minor scratches and stains where the varnish has chipped off. Even the smallest damage is immediately repaired, as the body would otherwise begin to rust. Rust sometimes spreads under a coat of varnish.
Tip 5: Clear View Through Clear Windows
Full spring cleaning of the car also includes cleaning the car windows, which form a fine mud veil - also inside. Headlights following cars and sunlight can be extremely dazzling. Windshield wipers and microfiber cloths help.
In the car, all parts of the body should be washed, starting from the roof and even ending wheel rims and rubber. It is also recommended to clean the underside of sills, bumpers and other items that are very close to the ground.
After cleaning, rinse the parts with clean water and wipe dry with a cloth. After that, the car must be left for a few minutes to dry completely. Thus, the first preparatory stage finished, you can proceed to the next.
Tip 6: Inspect your windshield for scratches and chips
It is also recommended to check them for maximum damage after cleaning the washers. In winter, sprinkles can leave small stone chips or scratches in the windshield. If they are ignored, the disc will still break out in the worst case scenario. If the stone is not unusually large and out of the driver's viewing area, it can be repaired in a workshop.
Tip 7: Check your wiper and replace your cleaning water
The windshield washer system ensures clear visibility while driving. After winter, you should check your wipers and replace them if necessary, as you may have to do heavy work during the cold season. It is also recommended to switch to a summer washer. Use a winterizing agent with antifreeze before using a new cleaner, as mixing can form solids that clog the pipes.
Pasting parts
The next step is the pasting of the machine parts. For this, masking tape is used, which is applied to all rubber and plastic parts. If we talk about embossed plastic, then the polishing compound is very badly washed out from it, so special attention should be paid to such details.
Tip 8: Thoroughly clean interior trim and upholstery
In winter, boots with a rough profile carry a lot of dirt into the car. Begin cleaning the spring in the cabin by roughly cleaning the leg areas. However, to remove stains on the seat covers, you must use a special upholstery. To clean fittings and other items on a car that are made of plastic, you must also use a dealership product that is adapted to the material.
Tip 9: Prevent Moisture, Prevent Mold Formation
Since the cold season often brings bad weather with rain or snow, moisture builds up in the car. They should be fought to prevent mold in the interior. Newsprint and heaters help with drying. Air the car regularly and leave damp rugs and carpets outdoors in good weather.
In addition, the masters recommend gluing the glass. This will help protect the glass if the compound is too liquid and splashes during operation. Also, do not forget about car logos and different nameplates. Ideally, it is better to dismantle them before work. At this stage, the pasting is over.
Bitumen cleaning
As a rule, bitumen and bituminous spots are located at the bottom of the car. Usually the bottom edges of doors, bumpers, sills and wheel arches are exposed to such contamination. It is recommended to use chemicals to remove such contaminants. It is worth wiping off the bitumen carefully so that there are no traces of it.
Tip 10: clean the trunk and check the accessories
When cleaning a car, the trunk is often forgotten. But moisture can also accumulate there. Check and clean the gaskets, spare wheel and seals. In the context of spring cleaning, it is also necessary to check the air pressure in the spare wheel and the expiry date of the mounting box.
Careful care is used to maintain the value of the vehicle. This is as important as an oil change or inspection. Varnish is affected by temperature changes, sun exposure, industrial dust or other environmental influences. Improper treatment also has this effect. Without attention, the varnish loses its gloss and its resistance. Constant external attacks cause the varnish components to be removed. As a result, the lacquer layer is destroyed after a long tent. This “breakdown” of the varnish can be prevented by regular varnish with suitable care products.
After the bitumen has been removed, the surface must be degreased. To do this, you can use any degreaser or anti-silicone. The wipes with which the composition will be applied should not leave any lint behind. It is important!
Clay processing
Today it is recommended to clean the body with blue clay. It is a natural material with some additives. Due to its structure, the clay will be able to capture and remove all residues of dirt and dust, and this will allow you to get a perfectly clean surface. Clay removes only solid dirt particles.
Dry after the surface of the laundry, leave the leather skin in front of the skin, do not use dry. Dispose of empty containers and used cleaning products in an environmentally friendly manner.
- Wash the car regularly and often.
- Thorough preliminary cleaning Remove aggressive substances immediately.
- Clean the vehicle at the wash pad provided for this purpose.
- Never try to clean the car.
Clay is used quite simply. It should be driven along the car body, and it should also be periodically moistened with water. To do this, you can use a spray. When the body is clean, the clay will simply slide over the surface.
Pasting openings
At the end of the preparatory process, all holes and openings should be sealed with masking tape. Thus, it will not be necessary to get out the remains of the polishing paste from them. Scotch strips should be no more than a centimeter. After pasting, you can proceed to the polishing itself.
Therefore, aggressive impurities should be removed immediately. Such aggressive impurities can be of biological or industrial origin, for example. In addition to exposure time, humidity, concentration and temperature also play a decisive role. Therefore, upon delivery of the vehicle, the task of the vehicle owner begins to contribute to the maintenance of the vehicle body and the painting of the vehicle. Regular Maintenance means that the aforementioned impacts should be kept as low as possible. Best paint protection against harmful effects on the environment - this is frequent washing and subsequent preservation.
- Therefore, these aggressive substances must be removed immediately!
- A safe way to prevent the consequences of these attacks is not yet available!
If polishing is not carried out at service stations, then it is recommended to choose a non-sunny day and not cold weather. Naturally, there should be no precipitation in the yard. It is recommended to work in the garage, as ultraviolet light dries the paste quickly. The garage itself should have good ventilation and good lighting. With the right lighting, the results will be more visible. Parts that could not be dismantled should be sealed with tape.
System technical condition Clean brushes Correct contact pressure Sufficient amount of detergent Additional wheel brushes and access. Correct temperatures.
- High pressure pre-treatment.
- High content of fresh water.
- Soft water.
- Tested and coordinated detergents.
- Antibacterial additives in the detergent.
Conclusion
Preparatory measures for polishing work are important stage... It should be taken seriously, as it depends on a well-conducted preparation. final result – appearance cars.
For a quality hand wash, the following points must be observed. Remove coarse dirt during pre-wash to avoid scratching the paint surface. Do not use household cleaners, but special paint care products. Observe the manufacturer's instructions. Do not wash your car in the blazing sun, otherwise water spots can easily develop.
- Spray the insect remover ahead of time and let it work.
- Use a special, large insect pore to clean the glass.
- Use a soft, clean sponge to clean your car.
- Use enough water to clean, rinse with clean water.
Several decades ago, in America, they developed and began to successfully apply sandblasting of a car, using soft blasting in car service and repair shops. Sandblasting metal is very effective remedy from removing rust, old primer and paint from the metal surface. The Nord Blast machines are capable of very delicate processing of thin metals, removing both one layer, such as dirt, and several layers, such as soil. This effect is achieved by adjusting the jet power. If you need to clean quickly, for example, thick metal, you can set the jet more powerful, then the processing process will go faster. Thanks to the use of soda and reagents, the treated metal will not immediately begin to rust again. If, during conventional sandblasting of metal, it is necessary to immediately start preparing for priming and painting, then in the case of soda and reagents, you will have more time, for example, to transport metal products to the paint shop.
Nano paint sealant technology
Our Nana plating service can be your car's quality sealing surface. The working process is similar to a lotus plant. Water, dirt and grime simply run away and the paint remains protected. Is shining your car like new and gaining vehicle value at the same time? After that, you can leave their vehicles appear in Long Lasting Shine for the time being.
In addition, cleaning the vehicle from the outside is made easier. Thus, it can be, for example, by applying a soil and a water-repellent layer, to easily remove dirt by insects or bird droppings. In addition, the rims can be fitted with nano-lacquer. It leaves a heat-resistant protective film so that dirt, dust, oil or water simply rolls off.
Since then, it has become one of the main ways of cleaning cars from rust and old paint and preparing for further work and painting, and has also become widespread in other industries. Another of important advantages processing is the fact that Nord Blast devices are mobile, if you order sandblasting services from us, we can come directly to the spray booth, process the car body on the spot, right at the spray booth! You can immediately start preparing the body for painting on site.
Benefits of nano sealant
We recommend nano-seal for paint and frames to be done as soon as possible, to be done after purchasing the vehicle, to give this protection and shine, so that you can enjoy your car. In the future, nanotechnology is very important. Here different kinds analysis and processing of materials are summarized. But when viewed under a microscope, it falls very quickly to what would seem to be smooth surfaces, but have rough structures. The dirt sticks to these structures later.
The main factors contributing to the popularity of the service of mobile sandblasting and processing of metal structures are the high speed of work performance, their relatively low cost and ideal condition any surface after processing with a mild abrasive compound.
Nanotechnology is used here. This effect is also called the lotus effect. This effect can be obtained by using our special gloss protection shampoos. The foaming product is the right choice for gentle hand washing, while maintaining a premium. It contains a unique combination of innovative cleaning and care components. In the application, a long-lasting dirt and water-repellent nano layer is formed on the car paint. Vehicle, thus, reliably protected from external environmental influences.
Professional processing of the body, frame and other parts is necessary when restoring cars
How does auto sandblasting work when cleaning a car?
Its main task is, all types of dirt and old paintwork.
It is very important that the surfaces to be cleaned remain intact and undamaged. If the car is a frame car, then first you need to clean the car frame, then the body and the bottom using blasting.
It is better to use abrasive substances with low density and hardness - Armex granules and dry ice crystals. Armex abrasive is a granule formed from chalk and soda. Compared to the sand used for sandblasting cars, soda has half the hardness, therefore, it cannot damage thin metal, for example, the underside of a car, and even softer surfaces such as plastic, rubber, glass.
The supply of abrasive to the surface is carried out using special devices that create the required pressure.
Industrial has the ability to regulate the pressure, with which you can control the thickness of the removed paint layer. When good condition it is quite realistic to remove only the paintwork without damaging the primer.
The cleaning of layers of dirt and various coatings occurs due to the energy of the "microexplosion" that occurs during the collision of the abrasive granules with the surface. When they break down, they simultaneously destroy and remove traces of rust and fuels and lubricants, dirt. During dry work, dust is generated in a small amount.
At the request of the customer, sandblasting and wet cleaning services can be used, mixing and spraying abrasive granules with water. This will completely stop the dust formation process. We recommend this method. The used cleaning material does not need special cleaning and disposal. As an environmentally friendly and water-soluble substance, it can simply be washed off with water. It is this property that makes it possible to clean engines or other parts of cars without disassembly.
Sandblasting steel structures with ColdJet
The CO 2 crystals used as a cleaning agent have a temperature of almost -80 degrees. In the process of their interaction with any surface, the top layer is instantly frozen. It becomes brittle and peels off easily from the base.
Further processing with dry ice has a mechanical effect that helps to remove deposits. Cryogenic blasting makes it possible to speed up the process of processing a car body by 2 - 3 times and significantly save on the cost of these works.
Its use provides high-quality cleaning of the body, lifting eyes and even parts of a very complex configuration. As a result of the significant temperature difference, dry ice evaporates very quickly, leaving the surface clean and dry.
In this case, in addition to the removed dirt or other substances, no secondary waste remains. This method is environmentally friendly, absolutely safe for people, does not require the use of chemicals, and is performed without dismantling the vehicle components.
