Click Class
Tell VK
Dear visitors, dear friends !!!
In this topic, there are several reasons for electric stove malfunctions that we have to deal with in our everyday life. Familiarization with this correspondence and related directly to the repair - will allow you to make your own decision and, to some extent, save your family budget. Consultations are provided to you free of charge and the reason for such publication is the ease of searching for questions of interest, as well as, as a general mailing of answers.
Do-it-yourself hansa oven repair
Hello Victor. Hansa electric oven. I faced such a problem: when I set any temperature to the oven, the signal light turns on and then does not turn off, although it should turn off when the set temperature is set. And when I put food for baking, it turns out that it is all on fire. The case and the knobs for adjusting the programs get hot, so it is impossible to touch, and then the clock goes out on the display, as if it were in a de-energized state. Then, when it cools down, the clock appears on the screen again, but in the 12:00 mode. What's wrong with her and how to help ????
Victoria.
Hello Victoria. From your question, I understood that the oven of the Hansa electrical cabinet is controlled by an electronic digital timer. I think you need to check the "timer control board". The signal light does not turn off due to the fact that the heating elements of the electric roasting cabinet are always on. That is, depending on the nature of the malfunction (burnout of one of the elements: capacitor, diode, resistor, etc.) of the timer circuit, the heating elements of the oven can work either in a constant mode, or they can not work at all (if an open circuit occurs). I believe that the electronic digital timer should be returned for repair, or replaced with a new one.
Victor.
How the hotplate is heated, temperature control
I connected a used Siemens HN322200 infrared cooker. How should the cooking zones behave at different power settings? The worry is that at the lowest power, violent boiling occurs, which is not always necessary. The hotplate switches on and off periodically. The instructions say that in position 1 (lowest power) you can melt oil. Something I doubt it, it will burn. Q: What is the principle of power regulation? How should it look externally? Should there be a change in the brightness of the heater or only a change in the on-off intervals. Does the burner switch on / off occur in the switch itself or on the board using a relay? If there were a diagram, a lot would become clear. Thanks for the answer.
Hello Yuri. I did not find data on your electric stove in my sources, I am interested in the control panel. I assume that the power switches of the burners are continuously adjustable. If this is the case, then a thermostat (relay) is built into the design of the burner power switch, with the help of which the burner is switched off and on in a timely manner (the principle of operation of the contact of the bimetallic plate, depending on the degree of heating). Of course, the heating temperature of the heating element (hotplate) will depend on the duration of the cycle (switching the hotplate on and off). In general, the burner power switch must be removed from the control panel, sent for repair or replaced with a new one. When removing the power switch, all the contact connections of the wires must be written on a piece of paper (mark for yourself) so that there are no problems with connecting the switch.
There will be questions for me Yuri, - write.
Why does the electric stove turn off, causes, troubleshooting
Hello. I have such a problem, I have an electric stove Dream 12 06 03 СБ (4 burners 220V).
When you turn on the oven, after a while, cotton occurs. At the same time, the machine turns off on the stove and there is a smoke over the comfort switches.
PS all the comforts work.
What could be?
Hello Andrey. The hob of your electric stove consists of two burners with a diameter of 14.5 cm and two burners with a diameter of 18 cm, the power switches are positional (if I am not mistaken). In case of this malfunction, it is necessary to inspect and check the contact connections of the wires:
with a switch for a frying electric cabinet (oven);
with the contacts of the heating elements of the frying electrical cabinet.
Also, you must:
check the heating elements of the oven for resistance;
verify contact group(contacts) in the switch of the cooking cabinet.
It is difficult to give an accurate definition of a malfunction, since it will require a visual inspection and diagnostics of electrical connections. The machine turns off for the only reason, this is an excess of the rated current due to an excessively low resistance in any specific area in the electric stove circuit. Replacement may be needed:
oven switch;
Heating element of the oven
or replacement of individual wires (with burnt ends) that have lost their insulating properties and resistance.
Malfunction of the electric stove, short circuit to the case, the cause of the malfunction
Hello, tell me please why did the electric stove start to shock? After all, this has not happened before.
Hello Maria. For your electric stove, you will need to inspect all contact wire connections:
with heating elements of the oven,
with burners,
with power switches
and so on. From my practice, there was a similar malfunction, when the foil (heat-insulating material of the oven) came into contact with the contact of the heating element of the oven, and the foil came into contact with the body of the electric stove.
Beko electric stove, oven malfunction, how to determine the cause
Hello Victor. In the Beko electric stove, the oven stopped working, turned on the oven to full 280 and turned on the airflow, it worked for 15 minutes and went out, the display went out in the oven and stopped heating, and the stove on top is working! What could be with her?
Hello Laura. In your electric stove, you need to check the electronic control module, that is, you need the participation of a specialist to inspect and diagnose the elements of the control module circuit.
Victor.
On this for now, all friends. Get familiar with the malfunctions of household electrical appliances and gain your experience in carrying out repairs. Follow the rubric.
Tweet
Tell VK
Click Class
Greetings. I have a question about the temperature controller. Is it possible to replace a stepless stepless switch with a step switch on a small two-burner hob? thanks
Hello! Such a problem, moved the stove to wash the floors behind it and something lit up from the side below, and stopped working altogether. What is it?
Good day! I have such a problem, the oven position switch on the electric stove burned out. Dream 12-03, I took it off and bought it, but I can't remember how it was connected, tell me which wire is connected to which contact, thanks in advance !!
Good afternoon, Victor.
At home, I saw that the plug was damaged - obviously there was a short circuit, one of the parallel plugs in the form of plates was melted.
can be repaired?
Thanks.
Good afternoon, Victor.
They gave the electric stove Rika, from a new building, supposedly new.
At home I saw that the plug was damaged - obviously there was a short circuit, one of the parallel plugs in the form of plates was melted.
A plug has two parallel plugs and one perpendicular below them.
Is it about the stove or the electrical network at home, where did the stove come from?
can be repaired?
Thanks.
Like any kitchen appliance, the oven can fail, which is always upsetting, especially if the warranty has already expired. What to do if the device has become faulty, what types of breakdowns can occur and in what cases the service center does not repair? The answers to these questions are presented in this publication.
When the equipment is under warranty
If the oven is out of order, and the warranty period has not yet expired, you must contact an authorized service center or the store where the product was purchased. A statement is written, on the basis of which the master comes and examines the equipment. If the breakdown is not difficult and he has with him necessary spare parts, repair of ovens, like any other appliances, can be done at home. Otherwise, the unit will be taken to an authorized service center, where the malfunction must be eliminated within 45 days.
If there is no fault of the buyer in the breakdown, and the craftsmen do not fit into statutory term, for example, due to the lack of the necessary spare parts or materials, the equipment must be replaced with a new one. Usually manufacturers give a one-year warranty, however, there are some firms, for example, VEKO, which give 2 years or more.
Even if the equipment is under warranty, repairs will not be made free of charge if:
- damage caused by voltage surges;
- the breakdown was due to an incorrect connection;
- insects or rodents have entered the cabinet;
- there are traces of an autopsy and self repair- scuffs, solders, scratches: in this case, repairs and spare parts will be paid, even if the breakdown was caused by the manufacturer.
If the warranty has expired
A completely different situation develops if there is a fault of the owner in the breakdown, or the warranty period has expired. In this case, people usually face a choice: contact the service, to a familiar master, or try to fix the malfunction with their own hands.
To begin with, you can try to independently determine what exactly is out of order. This will simplify the repair of the oven and will help the master to navigate even before he arrives at the address. When it comes to ovens, there are several common breakdowns.
Burned out heating element
If the cake is cooked for a very long time, it remains pale on one side, despite the fact that the maximum temperature is set on the regulator, then one of the heating elements may be out of order. It is quite simple to determine this - you need to turn on the oven for a few seconds, then touch the heating elements, having previously protected your hands with an oven mitt. If there is no heating, the elements must be replaced. These parts are usually inexpensive and can be easily replaced.
Thermostat is out of order
If all the heaters are working, the oven is set to the desired temperature, and the cake is still standing and has not been baked for an hour, it is possible that the whole thing is in the breakdown of the thermostat. It is quite difficult for an ordinary consumer to reliably determine such a breakdown at home, so one cannot do without calling a master.
Error codes
Electronic display models are very often programmed for self-diagnosis. In other words, when an error occurs in the system, they display information about it on the screen in the form of symbols. Each manufacturer has their own oven error codes, they are detailed in the instructions for specific models. For example, if the BOSCH oven does not turn on and the E011 characters appear on the display, then possible reason malfunctions - long pressing of one of the buttons, when jamming or sticking. Repair of ovens in such cases is not performed, such problems can be eliminated by hand, following the advice of the instructions.
Check for attentiveness
It also happens that malfunctions have nothing to do with the repair of ovens. We are talking about power failures, about a cord accidentally pulled out of the socket, about a not tightly closed door and other trifles. Oddly enough, because of such ridiculous accidents, oven owners spend a lot of nerves. Therefore, before you run to buy spare parts or call a master, you should make sure that the equipment is correctly connected.
Other breakdowns
These include a burnt out electronic module, a failed timer, damaged contacts, and much more. Repair of ovens in this case should be carried out only in service centers; it is quite problematic to fix such problems with your own hands.
Most buyers are concerned about the cost of spare parts. As a rule, when it comes to heating elements, thermostats and other components, then their price is low. The control unit is a completely different matter. Often, its cost is more than one thousand rubles, and in the event of a block breakdown, it is impractical to repair an oven that is already several years old.
No matter how expensive and high-quality household appliances are, in the process of prolonged or improper use, they can malfunction. This also applies to electric ovens. Even such well-known manufacturers as Whirlpool, Combustion, Ariston, Electrolux and Bosch cannot guarantee smooth operation their products in a variety of conditions. And if the warranty period has already expired, then you will need to repair the ovens yourself.
When the kitchen equipment is still under warranty
In the event that the oven breaks down, and the warranty is still valid, then you should contact the service center or the trade institution where the equipment was purchased for help. After writing the application, the master must come to the indicated address to inspect the unit. In the event of a simple breakdown or the presence of the master the required spare part, the device can be repaired at home. If we are talking about more complex cases, then the service center takes the oven, undertaking to return it within 45 days without any defects and malfunctions.
If the breakdown was not the fault of the owner of the oven, and the master could not completely eliminate it, then the company is obliged to exchange the appliance for a new one. As a rule, all well-known manufacturers, including Whirlpool, Combustion, Ariston, Electrolux and Bosch, provide a warranty period for their own products from 2 years.
However, even with a valid warranty, free repairs will not be performed in the following cases:
- Failure occurred due to voltage drops.
- Malfunctions are associated with an initially incorrect connection of the oven.
- The device broke down due to rodents or insects that entered its interior.
- If there are traces of self-repair or opening on the unit - all kinds of scratches, solders or scuffs. In this case, the repair of electric ovens will be paid, even if the breakdown is associated with a manufacturing defect.
What to do if the warranty period has expired?
If the warranty has already expired or the malfunction has occurred through the fault of the owner himself, then the repair of built-in ovens can take place in two ways - by professional craftsmen or by hand, as shown in the video.
First of all, you will need to independently determine the cause of the malfunction. If we are talking about a simple breakdown, then you can eliminate it with savings for the family budget with your own hands. If we are talking about replacing an expensive spare part, then it is worth entrusting such a responsible work to a specialized service center.
What kind of malfunctions can we talk about?
Most often, repair of Ariston ovens and other manufacturers is required when the following breakdowns occur:
- Problems with heating elements. If the dish is cooked for a long time at the maximum temperature, and at the same time one side of it is much paler than the other, then we can talk about malfunctioning of one of the heating elements. It is very simple to identify such a breakdown with your own hands - you just need to turn on the electric oven for a couple of seconds, and then touch the heating elements with your hand wearing an oven mitt. If they do not heat up, then they need to be replaced with new part... As a rule, spare parts of this kind are inexpensive and can be replaced with your own hands.
- The thermostat is broken. If all the heating elements work correctly and the temperature is set correctly, the dish has not baked even after a long time? We can talk about a malfunction of the thermostat. It is quite problematic to identify such a breakdown on your own, so it is better to immediately call an experienced master.
- Errors displayed in codes. As a rule, the Whirlpool, Combustion, Ariston, Electrolux and Bosch units with an electronic display are supplemented with a self-diagnosis function, as shown in the photo. If there are failures in the system, information about them in the form of symbols will appear on the monitor. Each manufacturer uses its own codes, which are necessarily prescribed in the instructions for the technique. Whatever error is displayed on the screen, you can fix it yourself, while following all the advice written in the instructions.
- Owners carelessness. It very often happens that the resulting malfunctions in the operation of equipment do not require repair of the electric oven. These can be power failures or accidental disconnection of the unit from the power source, the oven door is not completely closed. All these little things can bring the owners of household appliances a lot of problems, since, without trying to independently determine the cause of the failures, they immediately call the master to the house, whose services will need to be paid.
- Other types of breakdowns. Also, electric ovens may need to be repaired if the timer breaks, damaged contacts, etc. In such a situation, it will not be possible to fix the problems on your own, since professional skills and special equipment are needed to eliminate them.
Repair built-in ovens with my own hands possible, but if we are talking about complex breakdowns, then it is much wiser to entrust their elimination to specialized service centers... Otherwise, amateur performance may end up with more complex problems, which will be more expensive to fix.
