Have you noticed how many admiring, and sometimes envious glances stop at your Toyota Corolla, because the wheels that you have chosen give it such an original and unique look. This means that the right combination of practicality and uniqueness of the car's external appearance has been found. But do not go too far, because the main trouble lies in the details, follow all the recommendations for tuning wheels, and then driving will not bring you a lot of problems.
Rink selection
Disks, or rollers, operated by Toyota Corolla before 2012, can be steel or light alloy. Blanks for steel products are made by stamping. Conventional steel rollers are welded from these stamped blanks, but they are not resistant to corrosion and are difficult to balance. Such discs are easily deformed and easily straightened, but they serve quite a long time.
For cast products, an alloy of magnesium and aluminum is used as a material, and such rollers are made by casting in a mold or by forging. Alloy wheels are very lightweight and work optimally without loading the car's suspension, but they are more expensive than steel wheels. Forged products are more durable and withstand shock loads well, but their price is much higher than that of light-alloy ones.
Wheel rims loosening
The most competent decision will be the choice of original wheels for Toyota Corolla.
You need to understand why these rollers are optimal and non-destructive for suspension. In this case, it is necessary to deal with such a concept as wheel bolt pattern.
The manual for the Toyota Corolla spelled out what this notorious blabbering should be. It clearly states that in cars produced from 1999 to 2001, this parameter is 4x100 mm, and in subsequent years it became 5x100 mm. In fact, this means that the diameter of the circle on which the holes for the bolts (studs) are located is 100 mm, and the number of these bolts is four, and for later models - 5 bolts.
The bolt pattern has the designation PCD and is calculated as follows: the distance between adjacent holes for the studs (bolts) is measured with a caliper and the result obtained is multiplied by a factor of 1.701 - we get the bolt pattern of the existing roller. This parameter is needed in order to drill a custom roller, which has a smaller overhang and a larger diameter, and a wider rubber is placed on it.
Toyota custom wheels and bolt pattern
Choosing wide and large-diameter rollers for the car, we thereby increase the ground clearance, but the profile becomes smaller, the suspension system is more loaded and does not work out the unevenness of the road so confidently. The loaded body sags, the arches rub against the tires, and wheel wear is faster.
On the contrary, when the rubber profile is larger and the disc diameter is smaller, the stability and controllability of the car deteriorates, especially in corners and at high speeds.
So you need to choose custom rollers for Toyota Corolla only after calculating all possible consequences, and entrust the drilling work only to highly qualified craftsmen.
For the correct choice of a roller, you need to know not only the Toyota Corolla bolt pattern, but also such parameters as:
- The rim width - 75% of the tire width is the desired value.
- Reach or overhang is the distance between the roller mount and the rim plane of symmetry.
- The center hole of the disc should be equal to the hub seat.
- Rim Size - Usually measured in inches.
As for the bolt pattern of the Toyota Corolla over the years, the cars from 1999 to 2001 had a bolt pattern of 4x100, the extension of the roller is 38 to 45 mm. The size of the central hole (CO) is 54.1 mm.
Cars from 2002 to 2008, this also applies to 120 bodies, differed only in bolt pattern, it was 5x100. For the E 150 body, the stem changed from 2006 to 2013, it became 39 to 42.
For other models from 2002 to 2012, only the disc offset was different - 34 to 45. The bolt pattern from 2002 to 2012 for all models and bodies remained the same - 5x100 mm.
Conclusion
Only one conclusion suggests itself - you should not make a choice of non-standard wheels to please your ambitious plans, this only destroys the suspension and makes the car unstable and uncontrollable, exposing yourself and other cars to danger. There are many other ways to satisfy your ambitions.
Wheels and tires are key building blocks of a car. Not only comfort, but also traffic safety depends on the compliance of their parameters with the technical requirements of the car. The correct selection of wheels is possible based on the technical characteristics of a particular car brand. This review examines the technical characteristics of the wheels of three models of the popular Toyota Corolla. The Corolla rosebolt occupies a special place in this analysis.
Beautiful Corolla - Picture
Disks
The bolt pattern on Toyota Corolla is a design feature of the rim, which ensures its attachment to the car's hub. It consists of several holes located along its inner diameter. These holes then enter the hub pins.
Along with the term bolt pattern, the term drilling is also used. The bolt pattern is determined by the diameter of the circle, as well as the number of holes. The bolt markings take into account both parameters.
So, the drill hole of the Toyota Corolla modification has the formula 5x114.3. Here the number 5 indicates the number of holes and 114.3. the diameter of the circle in millimeters. However, the drilling formula is only part of the complete marking. This is how the full marking of the model looks like - 6.5JxR16 ET45 5x114.3.
The size of the disc is 6.5JxR16 ET45, bolt pattern and drilling - 5x114. 3. Or 7JxR17 ET50 5х114. 3.
To understand all the components of the marking, you need to paint what the numbers and letters mean in the size of the disk. Here is its transcript:
- The 6.5 indicates the width in inches and the J indicates the shape of the rim flanges. The shape of the flanges is important when fitting the rubber.
- In the abbreviation R16 in the letter R, the form of the disk design is encrypted. In Corolla, in all the models considered here, it is radial. This means that the spokes run along the radius of the wheel. The number 16 also denotes its diameter in inches. This parameter determines the size of the disks.
- In symbols and numbers ЕТ45 the parameter of disk departure is encrypted. Its value is equal to the distance between the plane with which it is pressed against the hub and the cross-sectional plane. ET45 marking shows 45 mm overhang.
White Corolla 180 on eye-catching rims
The manufacturer Toyota Corolla supplies solid alloy wheels. But for motorists, this detail is also an element of car decoration. Their choice is huge, since the market for this product is unusually developed. However, one must always remember that deviation from the factory parameters: in terms of weight, as well as dimensions, can be fraught with undesirable consequences.
11 generation Corolla tires
The wheel type mentioned above (6.5JxR16 ET45) corresponds to the size of Toyota tires marked 205-55 R16 91V. But to read this, you need to decipher the numbers and letters in the designation of the tire size.
Compliance is indicated by their common parameter R16, which shows the diameter of the tire rim. It is an error when this marking parameter is taken as the radius of the tire. The tire marking radius parameter does not exist.
Corolla E180 stock looks great
Figures 205 and 55 contain information about the width in millimeters, as well as the tire profile in%. The profile is the quotient of the width divided by the height of the tire, expressed as a percentage.
In the last three characters 91V, the load and speed indices are encrypted. The load index (91 units) shows the level of the maximum permissible load on one wheel. Knowing the load index, you can determine its actual size using a special table. Here the value of 91 units corresponds to 670 kg. V - speed index shows the maximum permissible driving speed for a given tire. Its meaning is also deciphered according to a special table.
Wheels and tires Toyota Corolla E 180 are supplied in two versions, in addition to the already discussed, these are also wheels marked 7JxR17 ET50 5x114.3, as well as tires 215-45 ZR17 87W. From the markings, we can say that they are larger than the previous ones, their width is already 7, and the rim diameter is 17 inches.
And finally, the recommended tire pressure for Toyota Corolla is 2.3 atm. However, this value should change depending on the speed of movement.
Black Corolla on huge wheels.
Wheels Toyota Corolla 150
Wheels E150
In the Toyota Corolla E 150 model, the wheel bolt pattern is made according to the pattern of five holes located in a circle with a diameter of 114.3 mm. The drilling of the disc has the already familiar 5x114 marking. By the way, the term drilling is actually the technology of creating holes by drilling.
Corolla 150 on 19 "rollers"
There are five types of discs available in the Corolla 150 model with this drilling: 6JxR15 ET39, 6.5JxR16 ET45, 6.5JxR15 ET39, 7JxR16 ET45, and 7JxR17 ET45. Their width varies from 6 to 7 inches, and the size of the disc ranges from 15 to 17 inches. The outreach is presented in two options: 39 and 45 mm. All types have the same rim flange (J) and radial design (R).
Roller parameters for the Corolla 150 are 6JxR15 ET39, 6.5JxR16 ET45, 6.5JxR15 ET39, 7JxR16 ET45, and 7JxR17 ET45.
Rubber for the 10th generation Toyota Corolla
For Toyota Corolla 150, the manufacturer provides five types of tires: 195-65 R15 91H, 195-60 R15 88T, 205-55 R16 91V, 215-45 ZR17 87W, 225-45 R17 93V .
Rubber for Toyota Corolla has a diameter of 15, 16 and 17 inches. The greatest variety in the tire model is introduced by the load indices, as well as the speed, all models differ in these parameters. But regardless of the listed features, the manufacturer recommends the optimal tire pressure of 2., 2 atm.
How do you like these discs for the Corolla 150?
Wheels and tires for Toyota Corolla 120
The drilling of the E120 disk is made in a completely different way than in previous models: 4 holes are located in a diameter of 100 mm. marked 4x100.
Great hatch
The parameters of the disc width, as well as the diameter, are represented by a large number of values. They are 5.5, 6 and 7.5 in width, and in sizes 14, 15, 16 and 17 inches. Large wheels make it possible for many car enthusiasts to dream of putting large wheels on their cars. However, it must be remembered that there are always pros and cons of large diameter discs. Four models have a disc overhang of 45 mm and only one 40 mm, all of them are radially shaped and have a J-shaped flange.
E120 disc marking: 5.5JxR14 ET45, 6JxR15 ET45, 6JRx16 ET45, 6JxR16 ET45, 7.5JRx17 ET40.
Corolla tires manufactured in 2006, as well as previous releases, since 2001, E 120 brands are also presented in five types; 175-70 R14 84H, 195-60 R15 88V, 195-55 R16 87V, 205-55 R16 91V, 215-40 R17.
Good rims for the 120, what do you think?
Corolla tires are unique in terms of the combination of parameters. The tire widths form a range of 175, 195, 205 and 215, which in combination with the profiles: 70, 60, 55, and 40, as well as the diameters: 14, 15 16. and 17, determines the unique size of each rubber type. The recommended tire pressure for all types of tires is 2.2 atm.
Rubber for Corolla
In addition to the standard size, the tires differ in the season of operation. According to this indicator, tires are presented as winter, summer and universal. To provide resistance to high temperatures, hard rubber is used for the production of summer tires.
For winter with negative temperatures, tires are made of soft rubber. Summer and winter tires differ in shape, as well as tread depth, presence of studs, which is due to seasonal characteristics of operation: frost, snow, ice in winter and heat, water, mud in summer. However, to improve the handling of the vehicle during the season, summer and winter tires are also provided with different tread patterns.
I've already seen these discs somewhere) (photo above)
According to the tread pattern, there are 3 types of summer tires: symmetrical non-directional, asymmetrical non-directional and asymmetric directional... Treads with symmetrical non-directional graphics are considered universal. They are used for moderate city driving. The tire with asymmetric non-directional graphics has a different pattern on the inside as well as the outside. These tires are optimal for fast driving on wet roads. The grooves on the asymmetrical directional tread form a swept pattern. Dry weather is ideal for driving fast with these tires.
Similarly to the summer season, there are 3 types of winter tires: studded rubber of the Nordic type, non-studded friction rubber of the Scandinavian type and non-studded friction rubber of the European type. Studded tires of the Nordic type are designed for driving in icy conditions at temperatures from zero to minus twenty-five degrees. Scandinavian type non-studded friction rubber suitable for driving on snow at temperatures up to fifty degrees below zero. Non-studded friction rubber of European type is used in warm winter conditions in the temperature range from five degrees Celsius to twenty degrees below zero.
Using automatic selection of tires and wheels for the car Toyota Corolla, you can avoid many problems associated with their compatibility and compliance with the recommendations of the car manufacturers. After all, they have a huge impact on a significant part of the vehicle's operational properties, primarily on handling, fuel efficiency and dynamic qualities. In addition, tires and rims in a modern car are one of the active safety elements. That is why the choice between them should be made as responsibly as possible, which presupposes the presence of a whole range of knowledge about these products.
Unfortunately, or, on the contrary, fortunately, a significant part of motorists prefer not to study the technical device of their own car thoroughly. Regardless, the automatic selection system will prove to be extremely useful, as it will minimize the likelihood of choosing the wrong rims or tires. And he, thanks to the widest assortment presented in the online store "Mosavtoshina", is very diverse.
Toyota's looseness is a sure step towards a unique car design. To improve the stability of the car and give it a unique look, the original discs are replaced with wider ones. It also improves the vehicle's handling and gives it a distinctive look. During the installation process, care must be taken to ensure that the tires have a low profile. These tires are arguably inferior in comfort, but provide better performance.
The bolt pattern of a Toyota Corolla car is one of the most important parameters that allows you to make a high-quality choice of wheel disks. The modern Toyota Corolla, launched on the market this year, does not require disc replacement. Diffusion can only be done as a last resort. Most often, such a replacement is made when the owner needs to replace it with more original design elements or because of any damage.
We change discs in case of damage to the car
One of the safest options for replacing disks during repair work is considered to be working in a specialized car service. Such a service will provide the owner with a special guarantee. In addition, specialists will be able to do the job much better than beginners, as they have the necessary experience and knowledge in restoration work.
When replacing disks, care must be taken to correctly select the right product. Naturally, it must be genuine. The manufacturer must take into account all the nuances of manufacturing the Corolla wheel system. It is necessary to ensure that the installation of specific elements is carried out with maximum reliability.
Not everyone can afford to order original components from a dealer, and in this case it takes a long time to wait for them. Craftsmen install analogs, and in order to determine the appropriate element, a bolt pattern is required. The term bolt pattern includes the selection of holes that hold the Corolla bolts. If this process is incorrectly carried out, it can lead to the fact that the disc will be located on an axial basis. The safety performance in this case will be noticeably worse.
Wryly placed elements will contribute to the fact that the suspension and steering system will lead to a car accident.
This parameter can be measured in several ways. To facilitate the work, professionals have created special tables, which indicate the basic information about each model. It rarely happens that you have to calculate the parameters yourself. A similar figure for Toyota, as a rule, includes PCD components with two numbers separated by a fraction.
The size of the wheel group parts for Toyota Corolla, as well as the tire pressure, you need to know for your model during maintenance, seasonal replacement, wear and road deformations. It is easier for the dealer of a car dealership to be guided by the specified dimensions of the parts than by the presented wheel or car brand.
The standard set of Toyota Corolla 1.33 wheels is fitted with 15-inch steel wheels with 195/65 R15 tires. Other versions are already equipped with other products - 16 inches and 205/55 R16 tires. Models with "Comfort-Plus" - complete set are equipped with details from light alloys. This equipment is also used for the Corolla 1.8 Dual VVT-i CVT and Corolla 1.6 Dual VVT-i CVT models.
The 11th generation Toyota Corolla has a wheel group with the specified parameters:
Wheels: ЕТ45 6JхR15 5х114.3
Tires: 91H 195 / 65R15
Wheels: ЕТ45 6.5JхR16 5х114.3
Tires: 91V 205 / 55R16
Drive conventions include:
J - the shape of the rim flanges;
6 - width in inches;
5х114.3 - number of holes for mounting and their diameter;
16 - landing diameter in inches;
ET - disc departure;
Departure is a standard value. Regardless of the design of the machine, the outreach for a given model should remain unchanged.
Photo 1. Symbols of dimensions of Toyota Corolla wheel parts
The legend of rubber includes:
205 -r width, mm;
55 - ratio of height to width (profile);
R - design view (radial);
16 - landing size (in inches);
V - speed index (V - up to 240 km / h. H - up to 210 km / h.)
91 - load permissible on the wheel 615 kg at standard pressure;
Photo 2. Symbols of the dimensions of the Toyota Sscrolla wheel with markings
Photo 3. Samples of wheels for Toyota Corolla with bolt pattern
Recently, car enthusiasts prefer casting to stamping. Cast samples in photo 3 are located in the lower tier. However, it has been noticed that stamped ones are easier to withstand the impact of road irregularities than cast ones. Even if a dent is formed in the stamping, it is often fixable. But the casting gives a crack and after that only needs to be replaced.
Toyota Corolla alloy wheels made of light-alloy materials do not rust and retain their good appearance for a long time.
Tire pressure
The most optimal pressure for Toyota Corolla among motorists is 2.2 atm. However, this value should vary depending on the speed of movement and the size of the rubber. Front pressure for 1997-2002 models by 0.1 atm. should be smaller than the back.
For R16 pressure depending on speed is recommended:
- 2.2 atm. up to 160 km. h,
- 2.5 atm. more than 160 km / h
Toyota Corolla wheel bolt pattern
Razboltovaya shows the layout of the bolts for fastening the wheel to the hub, the number of bolts and the size of the hole for the hub.
The standard bolt pattern of the Corolla is 5 x 100 with an offset of 35 ... 38 and a diameter of the holes for the wheel hub of 54.0 mm. The bolt pattern must be taken into account when changing the wheel group, as other models often use a different bolt pattern. These parameters are always indicated in the technical data sheet.
